Computer desk not only hides massive computer parts (processor, subwoofer, etc.) and numerous wires, but at the same time provides enough space for disks, books and other small things.
There are enough desks for a computer in the store roads. Independent making a table will save a lot monetary funds and will not take much time.
Types of computer tables
Options designs a lot of tables for the computer. straight and angled, compact tables and entire ensembles, including, in addition to the computer desk itself, all kinds of lockers, nightstands, shelves.
There are several types special tables, destined to install on them. laptop, ultrabook, netbook.
Very relevant for small apartments Transformation Options computer tables Same varied: table-cabinet, table-cabinet.
Yes, narrow closet does not take up much space, and, if necessary, turns into full-fledged computer desk and all constituents computers are in place, and you do not have to clean them every time.
Computer desk- pedestal
wall computer tables for laptop(netbook, ultrabook)
Mobile computer tables for laptop(netbook, ultrabook)
What can you make a table for a computer
Great option- computer from wood. You can also use other traditional furniture to create materials:
- laminated sheets
- MDF;
- plastic;
- metal;
- glass.
Note! A metal computer table with a glass top is the best solution for a high-tech interior.
Calculation of the size of a computer desk
Difficulty in sizing corner computer desk, so first consider just this option.
Corner table dimensions
Factors that affect the size of the table:
- Tabletop width. The minimum width of the worktop is 50 cm (500 mm). Optimal size- 60 cm (600 mm).
- Section width(which are the table supports). Each table has a different section width. If it is a processor tray, 20–25 cm (200–250 mm). If the tray with drawers or door is 45–60 cm (450–600 mm).
- corner depth(where the person is located). Minimum size- 50 cm (500 mm), optimal - 60 cm (600 mm).
Are common table dimensions are calculated based on the above sizes.
Side overlaps - 5 cm (50 mm).
Minimum table size
- table top width 50 cm;
- corner depth - 50 cm;
- section width - 20 cm and 45 cm;
- 5 cm + 20 cm + 35.4 cm + 50 cm = 110.4 cm - length of one wing table;
- 5 cm + 45 cm + 35.4 cm + 50 cm = 135.4 cm - the length of the second wing.
Optimal table size
- table top width 60 cm;
- corner depth - 60 cm;
- section width - 25 cm and 50 cm;
- 5 cm + 25 cm + 42.4 cm + 60 cm = 132.4 cm - length of one wing table;
- 5 cm + 50 cm + 42.4 cm + 60 cm = 157.4 cm is the length of the second wing.
Straight table dimensions
Dimensions direct computer desk calculated similarly. To do this, you need to know the width tray(or trays), working width places(50–60 cm) and overlaps(5 cm on each side).
Minimum table size
- with one tray:
5 cm + 5 cm + 20 cm + 50 cm = 80 cm; - with two trays:
5 cm + 5 cm + 20 cm + 45 cm + 50 cm = 125 cm.
Optimal table size
- with one tray: 5 cm + 5 cm + 25 cm + 60 cm = 95 cm;
- with two trays: 5 cm + 5 cm + 25 cm + 50 cm + 60 cm = 145 cm.
Height table varies from 70 to 76 cm.
Note! It is not recommended to make a table above or below the prescribed dimensions, as this will lead to an incorrect body position when working at a computer, the development and exacerbation of diseases of the back and spine.
Drawing of a computer desk with dimensions 
Materials and tools
On one's own do computer desk is not difficult. To do this, stock up materials and tools that will be needed in the manufacturing process and assemblies.
In addition to the base material (chipboard, MDF) you will need:
- glue PVA;
- pair guides for a sliding shelf (length - 30 cm);
- self-tapping screws or confirmations(furniture screws);
- dowels for furniture - 4 or 6 pcs.
You will also need the following to work. tools:
- pencils square;
- jigsaw;
- drill;
- screwdriver;
- hexagon;
- roulette;
- sandpaper;
- drill for confirmation.
Important! When cutting table parts from laminated chipboard with extreme caution, rounded parts should be cut with an electric jigsaw so that there are no chips.
Straight computer desk
Consider the manufacture of simple models.
Step 1. Cutting and processing wooden details for the future table:
- side racks 735 x 465 mm - 2 pcs.;
- central rack 735 x 380 mm - 1 pc.;
- back wall 1090 x 290 mm - 1 pc.;
- countertop 1200 x 580 mm - 1 pc.;
- internal shelves 450 x 250 mm - 2 pcs.;
- retractable shelf 830 x 380 mm - 1 pc.
Step 2 in the side and central on the rack we make holes for confirmations: 4 for each shelf. We strengthen bottom shelf.
Step 3 Fasten in the same way top shelf.
Step 4 We fasten back wall.
Step 5 We fasten the second sidewall with the help of two confirmations. From the front it will look like this:
Step 6 Marking a place for guides and proceed to fix them. When choosing or making sliding shelves, you should remember about thickness guides (1 cm on each side).
Step 7 Fasten guides to shelf.
Step 8 Drilling small holes in lateral racks (under the dowels of the tabletop). Similar holes drilled into the table top. You do not need to drill through the countertop, but the depth should be not less than 25 mm.
Step 9 Lubricated dowels glue PVA, insert them into the ends frame table.
Step 10 We put the tabletop on top and insert the dowels into grooves.
On the surface of the table, also on dowels, you can install shelves with drawers for small things, notebooks and disks.
Corner computer desk
Corner tables for the computer also come with superstructures and without add-ons.
Length wings:
- minimum - 110/135 cm;
- optimal - 132/157 cm;
- maximum - 166/200 cm.
Step 1. Draw and cut everything details future table. If for the manufacture of the table are used not laminated materials, antiseptic.
Step 2 Cut out countertop. We collect side racks with shelves (confirmations). Right section (which larger size) can be with retractable drawers or with one door.
If a section is made with boxes, then on internal side of the side walls are pre-attached guides. Boxes are collected, which are also fasten guides.
Step 3 With the help of confirmations, he gathers angular table support.
Step 4 Attached to it is a rectangular frame with guides and a retractable shelf for keyboards.
Step 5 in the tabletop, lateral racks and corner support holes are made under dowels(2 pcs on each side and 1 pc on each side of the corner of the corner support).
Step 6 Dowels pre-lubricated PVA, are inserted into the side posts and corner support.
Step 7 Installed countertop.
The sections at the back are closed with walls made of Fiberboard. We cover the finished table varnish or paint.
Computer table decoration
If in the manufacture of the table are used laminated wood sheets, then any special finishes not required. Process only visible ends details.
For this, a special edge ribbon. It is made from different materials and there are different colors.
The edge gives the product a finished and aesthetic appearance, and also prevents selection from Chipboard harmful for a person formaldehyde. On the ends of the parts, the tape is glued with iron.
How to make a computer desk with your own hands, see video:
Now almost everyone has a tablet or personal computer. And if you can work with the first two devices even while lying on the couch, then this will not work with a PC. Therefore, for the convenience and health of users, it is recommended to work or play on a computer while sitting at a specially equipped table. Today's review of the HouseChief editors is dedicated to how to make a computer desk with your own hands.
Read in the article
Design features of computer tables
They are designed taking into account the anthropological characteristics of a person and the requirements of GOSTs. standard height is 750-890 mm. Manufacturers offer modern models, which provide the ability to adjust the height of the table in accordance with the height of the user.
The depth of the tabletop is 600-900 mm, which allows you to choose the optimal eye distance between the monitor and the person sitting in front of it. Also, with such parameters it is possible more efficiently. If the depth of the tabletop exceeds 1000 mm, then “dead” zones are formed, which are problematic to reach without getting up from a chair or armchair.
The width of the table can be very different, and the larger it is, the better. On a large work surface, you can place additional monitors, printers, scanners, etc.
Types of computer tables
In mass production, computer tables are represented by two types: rectangular and angular. There are also semi-circular and U-shaped, but they are considered uneconomical in terms of free space and therefore are used mainly in office rooms and, as a rule, are made to order.
Linear or for PC has a rectangular table top, is characterized by low functionality and is intended for users with a small amount of equipment (scanner, printer, etc.). Under the tabletop, as a rule, there is a retractable console for the keyboard, as well as a niche or stand for the “system unit”. More functional models with 1 or 2 cabinets equipped with drawers. Often, a shallow cut is made in the table top above the keyboard shelf for the convenience of the user. This type of table is considered the easiest to make with your own hands.
Allows more rational use of free space. The table is multifunctional and ergonomic. This is the most popular type of furniture among PC users due to the fact that the table can be installed in a corner that is most often hardly used, it accommodates more office equipment and it has an increased working surface.
Table materials
For the manufacture of computer desks, a variety of materials are used: from traditional to modern. It all depends on your preferences and financial capabilities. The choice of material for the manufacture of the table largely depends on its design features.
- MDF and chipboard- the most popular materials for the manufacture of computer tables. This is due to the fact that they are durable, affordable, have a rich selection of colors and textures. However, if the edging of the ends of the parts is poorly performed, then the material is destroyed under the influence of moisture. In addition, tables made of MDF and laminated chipboard are not recommended to be disassembled and reassembled more than 2-3 times, as the places are broken and the hardware in them already “sits” not as firmly as before. You can also make a computer desk out of thick;
- tree – traditional material for making furniture. However, computer tables made of natural wood are very expensive and not everyone can afford it. As a rule, such products are chosen for decoration home office or executive quarters in offices. for PC are durable and excellent appearance;
- plastic. These are modern models that are perfect for rooms decorated in modern style, And . Modern plastic is very durable and has a large selection of colors, and also allows you to create tables of various configurations;
- metal + glass, MDF or. Combination of different materials allows you to create quite interesting designs that are durable and functional.
The necessary tools, fasteners and accessories for the manufacture of a computer desk
It is impossible to assemble a computer desk, as well as other furniture, without the right tool, and accessories. Let's consider this question in more detail. Of the hardware, you will need confirmations, screws, furniture, minifixes, rafixes and rondofixes (for hidden fastening).
Tools
- Electric drill and.
- Sander.
- (if the use of a "T"-shaped plastic edge is supposed to be used).
- Ruler, square and tape measure.
- Kit .
- Clamps.
- Awl.
- Pencil and marker.
accessories
- supports;
- furniture hinges;
- guides for drawers and keyboard console (roller or bearing);
- hardware;
- furniture corners;
- handles on the facades of drawers and superstructures;
- gas lifts for superstructure facades;
- shelf holders;
- decorative pipes with a set of clamps and fasteners;
- rollers for a mobile stand for a "system unit".
A simple computer desk: do it yourself
Classical rectangular table for a computer, even a novice furniture maker can easily assemble. It consists of minimum quantity details, and its design is quite simple. Consider how to make a PC table shown in the photo below. We will use chipboard as a material.
Construction drawing
To begin with, we make a drawing or sketch, perform calculations and draw up a detail with dimensions. For all these operations, you can use special programs or a notebook sheet and a pencil. By the way, it is very convenient to make a drawing on a piece of paper in a cage, taking each cell as 10 mm.
Watch a video that shows how, using a special program, you can make a drawing and calculate details from a photo of any computer desk found on the Internet
Part preparation
Detailed detailing will help not only when cutting a chipboard sheet, but also with the direct assembly of the structure. For normal computer desk small sizes you will need about 0.5 standard chipboard sheet. After the parts are cut and numbered, they must be edged, at least with melamine, and preferably around the entire perimeter of the blanks.
| Part number and name | Size, mm. | Quantity, pcs. |
| №1 Sidewall | 782×573×18 | 3 |
| No. 2, No. 3 Bottom, shelf | 400×543×18 | 2 |
| No. 4 Back wall | 907×490×18 | 1 |
| №5 Keyboard roll-out shelf | 900×386×18 | 1 |
| No. 6 Tabletop | 1400×604×18 | 1 |
Instructions for assembling a computer table step by step
In order to make the process simple and understandable, we offer step by step instructions With detailed description process.
| Illustration | Process description |
 | To begin with, we will make markings and drill holes in the sidewalls No. 1. The height of the opening from the edge of the upper shelf No. 3 to the tabletop is recommended to be 110-120 mm, from the bottom edge of the bottom No. 2 to the floor - 80-100 mm. We assemble the cabinet under the system unit as shown in the figure. At a distance of 80 mm from the upper edge of the middle and right sidewall, we install guides for the keyboard shelf. |
 | With the help of the back wall No. 4, we connect the cabinet for the system unit and the right sidewall, forming a single structure. Fill the furniture legs-studs on the lower ends of the sidewalls. |
 | on the sides and back wall screw metal or plastic furniture corners. We attach the table top No. 6 to the corners, insert the keyboard shelf No. 5 into the guides and check the ease of movement. Everything, the simplest computer table is ready. If desired, a special hole can be made in the upper left or right corner of the tabletop for. |
As seen to make straight the simplest table for a PC, you need a minimum of materials and experience, but at the same time, when marking and assembling a structure, regardless of its complexity, you need to be as careful and accurate as possible so as not to drill extra holes and not spoil the material.
We offer you to watch a video instruction on how to assemble a computer table:
How to assemble a corner computer desk with your own hands: drawings and diagrams
Do-it-yourself assembly of a home-made corner computer table is practically no different from the above-described option. The difference lies in the presence of 1 or 2 cabinets with drawers, an add-on for a monitor or documents, a large tabletop with a figured cutout opposite the user's chair and a pull-out keyboard board.
Drawings of a computer table with dimensions and cutting parts
The dimensions shown in the figure are approximate (except for the height and depth of the cabinets) and you can change them according to your requirements and preferences. The countertop is best milled and stuffed with a plastic “T”-shaped edge. It will protect the ends from moisture and deformation. Also do the detailing as in the previous version with a straight table.
How to assemble a computer corner table: step by step instructions
The most difficult and dusty work is cutting, grinding and milling the countertop. First, we mark the contour, taking into account the width and depth of the cabinet with drawers and the stand for the “system unit”. We make a hole in the corner of the table top. We stuff around the perimeter "T"-shaped or ordinary PVC edge 2 mm thick.
After the countertop is completely ready, we can start marking and drilling the rest of the details. It is better to immediately number the details in accordance with the detailing - this will make it much easier to assemble the table. Next, we act according to the following algorithm:
Recommendation! Mark the halves of the guides and install them on the sidewalls while the cabinet is not yet assembled. Believe me, it will be much easier and easier. To install guides, use a special template, of which there are many on the Internet.
How to make a computer table for games with your own hands
Computers are used for more than just work, and most users get happy, powerful machines specifically for gaming. An ordinary computer desk is not suitable for gamers because it needs a lot of space for multiple monitors, speaker system, MFPs, keyboards and game consoles. A gaming table can be purchased at a store or made by hand.
Drawings and assembly diagram of a computer desk
A gaming desk is practically no different from a traditional PC design. The difference lies in the larger countertop area, since you need to place at least 2-3 monitors, office equipment and game consoles. Also in cabinets instead of drawers for papers and stationery powerful speakers are installed. Game tables, as well as designs for ordinary working PCs, can be straight, angular and console.
Before assembling a computer desk for gamers, you need to carefully consider everything: how many monitors will be installed, what office equipment will be used, your preferences and capabilities. It is also necessary to provide a cable channel, since with such a large number of different equipment there will be a lot of wires and it is undesirable for them to hang out on their own.
Assembling a table for a gaming computer with your own tables
The manufacture of a gaming computer table is no different from the previous options, with the exception of a few nuances related to the design features. Watch the video tutorial on how to make a plywood corner table for a gaming PC
Overview of prices for computer tables
Modern manufacturers offer a fairly large range of computer tables, both for work and for games. We offer you to get acquainted with the prices of the most popular models. The cost of tables depends on the materials, design, brand and region of sale.
| Manufacturer and model | Material, parameters | Average cost, rub. (as of March 2019) |
|
| 12 590 |
|
| 4 420 |
|
| 28 000 |
|
| 4 719 |
|
| 3 630 |
|
| 7 600 |
|
| 5 950 |
|
| 8 400 |
quadro 
Ideas for a computer desk
Every user wants to be workplace was not only durable and functional, but also beautiful and original. And here they are faced with the problem of how to decorate a computer desk with their own hands. You can color it, decorate it vinyl stickers or glass inserts and create . We offer you to see a selection of photos with examples of the original decoration of computer tables.
For a comfortable homework it is not at all necessary to buy an expensive computer desk, it is quite possible to make it yourself. This item furniture can be assembled from the most various materials by choosing the desired shape and configuration. To make an angular one, one must not only choose the appropriate dimensions, but also determine what exactly the design should have, what functions to perform. Before starting work, it is recommended to draw up a detailed project or drawing, which will display all the required information (Fig. 1).
Image 1. Diagram of a computer desk.
Project for a computer desk
How to make a computer desk with your own hands without outside help? It will not only be necessary to create detailed drawing, but also calculate the materials, cut them.
Before drawing up a project, pay attention to the following parameters:
Image 2. Do-it-yourself drawing of a computer desk.
- table functionality. Consider if he should have drawers, sliding shelves, special stands for equipment and books;
- it is important to provide for the dimensions of the swivel chair so that the table is comfortable to use. Usually, standard sizes are taken, all office chairs almost do not differ from each other;
- for convenience, the height of the structure is selected within 700-750 mm, including the tabletop. If the table is made for a child, then its height may be slightly less;
- the dimensions of the office equipment to be installed must also be taken into account, so that later you do not mount an additional shelf for the printer. Do not be too lazy to take a ruler to take additional measurements of office equipment before making drawers and shelves;
- It is important to take into account the parameters of the room where the table will be installed. It is recommended to place it in such a way that the light falls correctly, the chair moves freely, and the seated person does not feel discomfort when using the furniture.
It is important when performing calculations on the drawing to indicate all dimensions, including the thickness of the side walls, countertops. This will allow you to quickly cut sheets of material, assemble easily and efficiently. The drawing should depict the location of the fasteners, their number. Pay attention to the picture how to do it correctly (Pic. 2).
Back to index
Materials and tools
To work at a computer, you need to prepare tools and materials. For work you will need:
- long metal and short rulers;
- simple pencil;
- end planer;
- square;
- screwdriver;
- jigsaw;
- drill, a set of drills, a depth gauge that will allow you to drill blind holes;
- Circular Saw;
- brushes for varnish or paint.
From the materials that are necessary for mounting a comfortable desktop, you need to take:
- MDF boards. It is necessary to take sheets with dimensions of 2440 × 1220 × 15 mm, during operation they are cut, according to the project. From such plates are made side surfaces, drawers and shelves;
- pine boards measuring 1200 × 150 × 25 mm, you need to take 2 pieces, they are used to strengthen the structure;
- for fasteners, it is worth taking 120 screws, dimensions - 3 × 15 mm, the head must be countersunk;
- ties for the corners of the plastic structure - 40 pcs.;
- sliding guides, the number depends on the number of drawers and drawers;
- self-adhesive or end edge, which will form the edge for shelves and drawers;
- sanding paper for edging;
- wood primer, varnish or paint for finishing.
Back to index
Table assembly
You need to start work with the assembly of the side parts. Guides are screwed to the surfaces of the boards; they are necessary for drawers and shelves. After that, all the side modules are assembled on the dowels. It is recommended to add PVA construction glue to the sockets, it will make the fasteners more reliable. To strengthen the fasteners, you can insert thin wooden planks into the nests. Assembly example in the figure (Fig. 3).
As the main material for the side walls, you can use ordinary fiberboards, but it is best to take MDF sheets with a thickness of 10 mm.
Image 3. Drawing of a computer table with upper shelves.
Such walls are perfectly fastened with self-tapping screws. Next, the table is assembled with your own hands using spare parts for drawers. For the assembly of boxes, MDF 10 mm thick is used. During installation, it is important to strictly observe right angles, since it will depend on how easy and convenient it will be to use the boxes. All dowels are inserted neatly into the sockets, which, for reliability, are best smeared with glue.
The side cuts of the shelves are pasted over with an edge tape, it is enough to iron it with an ordinary hot iron. To protect the tape, it is best to use a strip of paper to prevent the edge from blistering. If necessary, the excess edge is cut off with ordinary scissors, but this must be done very carefully. Wooden planks are glued to the front and back sides of the shelves, while their dimensions must fully correspond to the parameters of the part. This is necessary so that the sliding shelf can move freely along its guides.
Making a computer desk with your own hands is not so difficult, and as a result you will get irreplaceable furniture, because computers are in every home today, and it is much more convenient to use furniture specially designed for this instead of the usual one.
Today on the market you can find a wide variety of computer tables - a transforming table and a corner table are especially popular, because. they are not only comfortable, but also look original.
But, what is most pleasant, you can make almost any model of the table you like by yourself, after selecting it from the photo.
In the article you will learn how to make a computer desk, what tools you will need for this and how to properly mount the parts so that the furniture will last you a long time.
Drawings are the first thing you need when creating a computer desk. You can take ready-made drawings, or create your own, suitable for the size of your room.
Drawings are needed not only to see what the design will look like, but also to calculate the amount of materials and the price that it will cost you to build a computer desk.
First of all, decide on the appearance and functional elements of the computer desk: do you need drawers, pull-out shelves, stands for things, etc.
The more there will be additional elements, the more difficult it will be to make the table, but the more functional it will be in the end.
You also need to correlate the size of the structure with the size of the chair or chair that will be used for sitting.
This is necessary so that the table does not turn out to be too low, or, conversely, high or simply uncomfortable.
As a basis, you can take the standard size of any office chair, because. they differ little from each other.
The shape of the computer desk is another important detail.
It can be the usual rectangular, angular, or you can make a transforming table (see photo), which can change shape depending on the need.
The last option is the most difficult to manufacture, but you can assemble it if you wish.
The optimal table height is about 700 mm for an adult, and 600-650 mm if the furniture is planned for a nursery.
If you are making shelves for a printer, scanner and other office equipment, then you need to first measure it and find out what size the final size of the shelves should be.
The size of the computer desk is also affected by its location - try to ensure that the place is properly lit, the chair can move freely, and in general there is enough room for movement.
The final scheme should reflect the size of all parts, as well as the thickness for the side walls and countertops.
A high-quality drawing is a guarantee that you can easily and quickly cut the material and make details correct form and size, which greatly simplifies their installation and connection with each other.
The drawing should also reflect the amount of detail - look at the photo for an example of a diagram before you start creating your own.
After the drawing is ready, prepare the tools that you will need for further work.
Most often, chipboard is chosen as the material for the table, because. it is the most economical, and at the same time high-quality and durable.
In addition to chipboard, you can use natural wood or MDF, but then making the table will be more expensive.
In addition to wood, you will need the following tools:
- jigsaw;
- hacksaw;
- grinding machine;
- screwdriver;
- drill;
- roulette;
- chisel;
- square.
As you can see, there is nothing specific here, and, most likely, you can find these tools at home or in the garage.
Table manufacturing and installation
Do-it-yourself corner computer desk, a transforming table, as well as a regular rectangular table are made almost the same.
To make the simplest version of the design, you will need a chipboard plate with a thickness of at least 16 mm.
They begin work on assembling a table of any type with the selection of parts that will fix the structure on the sides.
Guides are screwed onto the boards, which are needed if you want to make drawers and shelves for your computer desk. Then the side parts are assembled on the dowels.
To make the fasteners work better and fix the parts as much as possible, add PVA glue to the nests, or insert wooden planks there. The walls themselves are fastened with self-tapping screws.
The following parts must be assembled using parts to create drawers. It's better for them to choose Chipboard thickness smaller than the rest of the table - about 10 mm.
Installing the boxes Special attention pay attention to the corners: they should be straight so that the drawers of the table slide out and slide in easily. Lubricate the PVA sockets, and after that you can install dowels.
Then you need to paste over the side cuts with an edge tape so that it lies tightly, you need to walk along the tape with a preheated iron.
But before that, put a sheet of paper on top, otherwise the surface may become covered with bubbles.
If you see that the tape is wide and extends beyond the edge, then cut off the edge with scissors, but do it carefully so as not to damage the coating.
So that the shelf can easily move along the guides, on its outer and inner side you need to glue wooden planks, the size of which matches the part.
If the elements do not match, then the shelf will jam, so pay special attention to this moment.
Look at the view of how the shelves for the computer desk are assembled - it will help you do the job better.
The tabletop is the last component of a computer desk. Before starting its installation, you need to make markings on the chipboard, noting the places where the countertop will be attached to the supporting pedestals.
In these places, you need to drill non-through holes, having previously installed a limiter that will allow you to control the depth of the hole.
The cabinets are installed on the countertop so that the holes are directed upwards. They will be connected by stiffeners, which will make the structure as stable as possible.
Wires will also be placed here, which will make the computer desk more convenient to use. As supporting elements, you can also use parts of the corrugated pipe, which will become a support.
The next steps are to fix the plinths on the pedestals, then turn the structure over and install the hinges on which the side door will be held.
You need to fix the structure with screeds so that it can be easily disassembled and mobile - if desired, you can easily move the table to another place.
It is best to make a monitor stand on the table top: for this, first make a frame (small wooden round bars) and secure it with glue and dowels.
You can also purchase a ready-made stand by fixing it with self-tapping screws.
The last step is the processing of the chipboard table. It is best to varnish the surface, but you can also paint it in the color you want to match the furniture. general style your premises.
If you decide to paint the structure, then first treat it with a primer. After applying the coating (lacquer or paint), it will be possible to use the chipboard table in 2-3 days, when the coating dries.
Computer table-transformer is done in the same way regular tables, ordinary chipboard is also suitable for the material, but there is scope for creativity: for example, a transforming table can be made with a turntable, or it can increase in size, and then you can use it not just as a place to install a computer, but also a full-fledged canvas to receive guests.
To do this, you can make the monitor stand removable, or completely abandon it.
Another unusual and popular option is to hide a transforming computer desk in a false cabinet, which you can also assemble yourself.
This is very convenient for small apartments, because in this way you save a lot of space.
In addition to the transforming table, in such a cabinet you can install shelves for books or documents - then everything will always be at hand at your workplace.
Finally, classic version- when the transforming table has a sliding panel, which, if necessary, increases the working space.
This is relevant, for example, if there are several children in your family, and they need to do their homework at the same time.
Other options for how a transforming computer table may look, look at the photo.
You can combine several, or come up with your own. original version, with the necessary skills and supporting videos, you can make almost any design model.
With the ubiquity of computers, there was a need for tables on which a monitor, a system unit, a keyboard and various office equipment could normally be placed.
Therefore, in our article we will consider the question of how to make a computer desk yourself. This task is quite feasible for ordinary person having little knowledge and skills in carpentry.
Having made a computer table with your own hands, you will not only save money, but also choose the ideal dimensions for your room, and also get aesthetic pleasure from the work done.
In contact with
Classmates
Types of computer tables
There is enough a large number of types of computer tables and its varieties - a laptop table, which has a much simpler device and smaller dimensions.
- Rectangular computer table which will easily fit into any interior. Usually it is equipped with a sliding table top for the keyboard and a bedside table for the system unit.
- Folding tables. Designed for people using a laptop. Very comfortable portable structures made of plastic and metal.
- Corner computer desk. If you have a free corner in the room, then it's time to put a corner computer desk there. This way you save space, and besides, it looks more compact than it actually is.
- U-shaped computer table will allow you to feel like in a study, thanks to its shape and, in addition, it can accommodate almost any additional devices. The main disadvantage is the large footprint.
- Semicircular table stands out for its design among other designs and the ability to place all the additional attributes in it. But there is a drawback, like the previous option - this is a fairly large space occupied.
Laptop table
When buying a laptop, users have a standard problem that can bring a lot of trouble. When working for a long time behind this device, all parts of the body begin to numb. To avoid this, special mini tables are made for laptops, which are much simpler in design than computer tables, but the price for them is sometimes very “biting”. Therefore, a do-it-yourself laptop table can become quite convenient exit out of position.
Table designs
There are several basic table designs, which we will discuss below.
- The most simple design comprises wooden tabletop, usually made of beech, and two legs, which are two boards. The beech board is sanded fine and covered with a double layer of varnish.
- A table with folding legs is more convenient to use, as it can be folded after work, and it will take up minimal space in your apartment.
- A variation of the second design, but with an addition in the form of a cutout for a mug. This table is very convenient for watching movies in the supine position.
- Another option is a table with folding legs, a place for a mug and two armrests. His photo is shown below. This is a more complex design, which, nevertheless, does not present great difficulties in manufacturing.
At independent production these products it is recommended to use a beech board, 1.8-2 mm thick. In this case, the table will last enough long term. As you can see, all these species do not represent too much complex structures and can be made by a person without special skills and knowledge in carpentry.
Tools
Let's see what tool you might need to make homemade table for a laptop.
- Hacksaw, preferably for metal. Using cutting tool wood, you will have to spend extra effort and time to process the edges.
- and a drill to it, of small diameter.
- Measuring tool (ruler, tape measure and possibly a square).
- Pencil.
- Fine-grained sandpaper for processing countertops.
Instructions for making a computer desk
The simplest version of the table will look like this. A tabletop that combines legs, which are two boards.
Note!
All these details can be cut out of old unnecessary furniture and then such a product will cost you almost free.
Everyone chooses the dimensions of the parts for themselves, but, for example, for a 15-16-inch laptop, the dimensions of the table top can be 60 * 28 cm.
The sidewalls for such a table are made bevelled and the length of this very beveled side should be 28 cm. This side of the leg is attached to the tabletop. The most convenient slope for such a table is when the back of the leg rises by 29 cm, and the front by 21 cm. This slope will be the most optimal for working in a lying and reclining position.
Sawing table parts
Computer desk
To make a computer table with your own hands, you need to make a lot more effort than making a table for a laptop. The main task in this case will be to make a table “for yourself”, because the store version may not be suitable for your complexion at all. Before you start making a table, you need to decide on its model. A fairly common model looks like this.
The computer is located on the table, the system unit is on the side under the table on a separate stand. Also, under the table on a stand, only in the center, there will be a printer and a place for disks and documentation, and the keyboard and mouse will be located on a pull-out shelf under the computer.
Detail drawing
Computer desk dimensions
After you have decided on the model, you need to draw up a drawing with dimensions.
The main size of any table, including a computer one, is its height. For a person of average height, it usually varies between 700-750 mm. For greater convenience in use, legs with adjustable height can be provided. This will be especially convenient if the table is intended for children who tend to grow. Then the legs unscrewed in height will not allow to spoil his posture. The height of the printer shelf must be at least 20 cm, in which case you can also store discs in a standing position on it.
DIY computer desk
Countertop manufacturing
The next step is to make the table top. Moreover, its size should not be too small and at the same time not be infinite. Everything should be compactly placed on it and, moreover, created as much as possible. comfortable conditions for work. Standard sizes countertops vary between 1-1.3 m, and the depth can be about 60 cm.
Note!
For greater convenience, it is necessary to provide a side at the back of the table.
This will prevent objects from falling behind the table, and its height is sufficient no more than 5 cm.
Shutdown
The size of the pull-out shelf will be only slightly smaller than the countertop, and the depth must be provided with a size of 40 cm. The final step when self-manufacturing computer desk, there will be a shelf for the system unit. The height from the floor level may not exceed 10-15 cm, but the width must be provided for at least 25 cm, so that there is the necessary distance between the wall of the shelf and the system unit for the normal operation of the computer. Thus, fulfilling all these requirements, you can effortlessly make a comfortable desk for your computer. well and visual material in the manufacture of such a table can be obtained by watching the video below.
DIY computer desk video:
In contact with
See inaccuracies, incomplete or incorrect information? Do you know how to make an article better?
Would you like to suggest photos for publication on a topic?
Please help us make the site better! Leave a message and your contacts in the comments - we will contact you and together we will make the publication better!
