Table lamp with your own hands from improvised materials. DIY lamps and lamps: the best ideas and master classes. Creative homemade shades for lamps, floor lamps and chandeliers

In this article, we propose step by step master classes how to make do-it-yourself table lamps from improvised means that are always in the house. It would seem at first glance ordinary and unnecessary things, but from them you can make original and designer lamps for desktop.

The most popular and simple improvised materials are: glass bottles and jars, cardboard and paper, plastic vessels, water pipes and cement. How to make lamps out of this we will show and tell in this article.

With a simple and elegant copper table lamp, you can decorate any corner of your home with your own hands. She will fit in perfectly modern interior from loft style to rustic. Prostate and conciseness - this is the main trump card of this table lamp.

For this you need tools:

Roulette, marker
Pipe cutter and washcloth
Wire stripping and stripping tool
Pliers and a thin flat head screwdriver
crosshead screwdriver

M materials:

Copper pipes
Acetone and super glue
Copper corners 90 °, 7 pcs.
electrical wire
Plug and Electro chuck
Switch and light bulb

Table lamp assembly technique

To get started, take a tape measure, marker, pipe cutter, rag, copper pipes and acetone.

Marking and cutting tubes

Use a measuring tape and a marker to mark where you will cut the copper pipes.
Do this carefully, accurately measuring every millimeter, because if the details are different, then in the end result they will not be as large as they should be.

Point the pipe cutter and adjust the diameter of the pipe with the nut. Look at copper tube, gradually readjust diameter with nut, so that the closure goes on until the pipe is cut.
After, with acetone and a rag, you can wipe the markings from the pipe.

TIP: Our parts have: 3 cuts of 15 cm, 1 cut of 20 cm, 1 cut of 45 cm, 1 cut of 25 cm. We used 12 tubes. When designing your luminaire, please note that the size of the copper cubits will be added.

While the cable is inside, we connect the parts

Paste the pieces together and glue super glue. In order to avoid problems in the future, it is better to glue each part and put it together.

Despite the instantaneous effect of the adhesive, it is preferable to wait a few minutes before proceeding to make sure the pieces are glued perfectly.

Tip: It will be more convenient to apply glue if you use a brush. If you want the lid to be at the very top, install it first. So the first part will be ready, and the cable will go in the other direction.

Tools:

Wire stripping and stripping tool
incisors
thin flat screwdriver
crosshead screwdriver

Materials:

fork
electro chuck
switch
Copper pipes
electrical wire

Install electrical system

Open the faceplate of the cover and start by stripping the insulation. Connect ground ( Blue colour) and phase (brown, gray or black) using the two screws you find inside.
Repeat the same process in the plug and switch.
In the switch you will find two pairs of small screws, a cable that you must cut to the height you want the switch at and connect to the appropriate sockets by going inside the small screws.
All you have to do is screw in the light bulb to make your copper table lamp.

Finally, put the lamp in a corner or place you like, and you will see how it will become a wonderful addition to your interior, illuminating the space!

Master class: Table lampfrom paper

When I first saw the Robert Delta table lamp, it was love at first sight! The shape is amazing, it comes in a variety of bright colors, just the way I like it. Recently I thought, since the accessories were amazingly durable, why not use them for the lamp?

Here are all the materials used:

old lantern or lamp kit
template and thick cardboard or paper, you can take polypropylene sheets
glue and putty
sanding block (medium + fine)
wood block (add weight to base)

Tools:

artistic ribbons
metal ruler / xacto knife
drill (can optionally replace xacto knife)

Lamp manufacturing technology

First, print the pattern (6 of each triangle) (1 of each hexagon).
Cut out the shapes so that they fit snugly on the board. Then use glue to attach the pieces to the back of the mat.
Using a metal ruler and a Xacto knife, cutting board, cut each shape.
Put them together.

Next, glue the bottom (shapes 2 + 4) to the base (shape 6). The triangles fit together nicely and if you did everything right, they will just fall into place.

Then use small pieces of art tape to stick them together and wait for the glue to dry completely.

TIP: Use super glue, it dries instantly (we used Aleene). Apply glue lightly, and wipe off excess.

After gluing the lower half (forms 2 + 4 to the base, turn the form 6 upside down (open end down), place the square on flat surface and let it dry overnight, this will help keep its area.
The next day, start working on the top of the lamp. Glue the 1 + 3 shape, leaving a little hole to insert the lamp inside. The top one (form 5) was glued along with the art tape, but it is not glued to the form 1 + 3 yet.
Then reinforce the seams with glue inside.

Then start working on the base of the lamp.

The level at the bottom of the lamp needs to be made a little larger, so cut a few 1×4 pieces to raise it a bit. Additional weight will also be added, which will give it more stability. Use screws to attach 1×4 to existing metal base. (We swapped the existing stem with one from another lamp to get it to the correct height).

Next, drill a hole for the cord and insert the plastic sleeve from the old lamp. The lamp should be disassembled, and pull the cord and wire through the threaded rod of the hole in the new base. Glue it in the center inside the lamp.

At the top (form 5), mark the center and drill a hole for the center rod. Then glue it in place.

After applying the adhesive, wipe off excess and, if necessary, lightly and apply a second coat after sanding.
Medium-grit putty and fine sandpaper, finish with a sanding block. At this point, you will notice its strong base.

When you've finished removing the dust, apply paint! To cover the top of the threaded rod, use the top of an old lamp - it just slides over the rod. Then return back to the nest!

Everything, a handmade table lamp is ready.

Bottle table lamp

Tin lamp

Such a lamp is perfect for a home desktop, both for a student and a schoolboy. Boys will especially appreciate it, it looks more like a transformer and a robot from the future. You can paint or decorate the jar itself with paper, thread, or make it more embossed. How right.

Table lamp made of plastic bottles

Plastic bottles can always be found on the farm, so decorating an old table lamp is not difficult. Usually, when restoring old lamps, the bases are left and plastic is used for the lampshade. The lampshade mount is usually used the old one. When working with plastic bottles, remember that cutting them is easier. paper cutter or construction knife. Glue is used for rubber or special for plastic.

Table lamp made of branches and cuts

Wood in the interior is always a classic - it is always fashionable and relevant. Decorating a table lamp with a cut of wood or old driftwood with your own hands, you will receive designer item which simply has no price.

To do this, we need to pick up any piece of wood we like, process it properly namely, dry it, apply impregnation from pests and cover it with varnish.
The second stage is to mount the top from the old floor lamp into the base. If this is not the case, it does not matter, in stores everything for light usually sells bases for lampshades.

Other original ideas

The basis for a table lamp, in principle, can serve as any object that you do not need: these are children's toys, Sewing machines, unnecessary socks and so on. Experiment and create beauty!

Reading time ≈ 8 minutes

Everyone dreams of decorating their home with stunning lamps made by hand from improvised materials on an individual basis. unique design. These original products able to transform not only a separate room, but the whole apartment. To have an exclusive thing in the form of a sconce or lamp unusual shape You don't need to buy expensive materials. All you need here is improvised means, your imagination and a little creativity. Consider the most best ideas and homemade decor options.

Original pendant lamps-mugs

Masterpieces from simple materials

Plafonds and other lighting devices can be made of almost any material that can change shape or be divided into several parts. It can be wood, plastic, metal, paper, glass, and even individual household items. Old bottles, records, dishes, toys or musical instruments, but the main component is still a light bulb.

That is why it is important to ensure that the lamp does not get very hot and is safe for others. Otherwise, it all depends on your imagination and capabilities.

Room lamp in a textile lampshade on a marine theme

What criteria are taken into account when choosing a lamp model:

overall design of the room;
interior design style;
the size of the room and the height of the ceilings;
the level of illumination and the number of window openings.

But not always the creation of a product can be planned in advance. Sometimes the materials themselves, found at home or in the garage, can lead to the idea of creating a real masterpiece, as in the photo.

Wall and table lamps from old utensils and equipment

Consider a few unusual options:

from tin cans great idea for arrangement of a workplace, it is possible to put both in an office, and in the student's room. If desired, the jar can be decorated with paint, threads and even draw a beautiful print;
from hangers - it is better to use wooden ones, sanding each and adjusting to the desired size. In this case, you can create any shape, as well as cover such a lampshade with paint;
from wood cuts - wood will always be relevant and fashionable for interior decoration. To create a unique design item, the saw cut must be well processed, dried, covered with a protective solution and the top of the old lamp installed. IN last resort the base is used under the lampshade from the store;
from glass bottles- Time spent on work cannot be considered wasted. After all, the result is such beauty;
from old drums or sports equipment - the products look very unusual, suitable for decorating a teenager's room, office or country house. drum set and old skis perfect solution for your own restaurant or office, as in the photo;
from small bicycle parts - the first such idea came to the mind of designers from Texas. Artists have built balls from small parts of old bicycles;
pumpkin lampshades - beautiful patterns are cut out on the peel, the pumpkin itself is dried, and a light bulb is placed inside. This will become a real masterpiece and will please the household for a long time;
from paper cupcake liners - fixing them in a circle, around the main lamp, you can make a beautiful night light for a nursery or bedroom;
from a set of graters - kitchenware can be useful and sparkle beautifully over your head, creating a special charm in the interior, as in the photo;
lace lamp - these are products from openwork napkins and knitted handkerchiefs. The fabric is covered adhesive composition for fixation;
in cutlery - if a lot of spoons, forks and knives have accumulated, and it's a pity to throw them away, create amazing compositions for decorating kitchen sconces and chandeliers. Cutlery can be fixed with wire, rope and glue;
hanging sconces in cups - will come in handy on cozy evenings for tea in the kitchen or in the summer;
from a colander is great option for any . It is better if the product is enameled, but such a lamp can also be painted in any bright color;
wire - this is the most simple idea for Hand-Made, because any beginner can cope with the manufacture. All you need is wire bright colors, spray paint and steel wire;
from veneer - the material can be woven into a round ceiling, and the parts can be fastened with an adhesive solution. You can use the veneer left over from the repair;
from a rope - in the conditions of a modern city, with the help of such a lamp, you can create at home a cozy atmosphere of a real province and rural comfort;
from branches - this is an extreme design, suitable for Eco, Country and Loft style. Branches can be gathered together with jute rope, giving them almost any shape. Compositions are created different sizes, varnished or left unchanged;
from large beads and stones - such a chic design will transform any interior. Beaded lampshades are an excellent decoration for any bedroom, living room or;
from an old wheel - even it can be used by cleaning it of rust and covering it with paint of the desired shade. Light bulbs are placed around the perimeter in any order;
shade self made from old photos can decorate a table lamp or a floor lamp, as seen in the photo;
from tongues from cans - suitable for this cans from soda, beer and just canned food. It will take some time to save rings, keys and tongues so that there is enough to create a lampshade or ceiling.

All lamps or lamps made by hand from improvised materials can have a different configuration. Optionally, it is possible to make both a floor, desktop and suspended model.

Spoon chandelier

Not always to create original interior you need to buy expensive designer furniture and accessories. Decor and other items can be made independently from simple means. Consider a master class on making a room chandelier from plastic spoons - you can do the job in just 30 minutes.

Required materials and tools:

a large number of disposable plastic spoons;
empty plastic bottle;
glue;
chandelier cartridge;
scissors and knife.

All labels must be removed from the surface of a bottle or any other plastic container using soap solution. Then blanks are made from spoons, while the handles are cut off. The parts are fixed with glue to the surface of the bottle; here it is important to follow a certain order or a planned combination of rows and colors. Cover the container in a circle, making sure that there are no gaps and visible excess glue.

Plastic chandelier made of white spoons

Glowing ball of threads

This perfect solution for a nursery or bedroom in Shabby chic style. To create a chandelier-ball in a delicate design, you will need to purchase:

glue;
thread or bundle of any suitable shade;
balloon;
petrolatum;
needle;
plafond.

First you need to prepare by inflating and tying the balloon, and then coating it with Vaseline. In a tube of glue, we make a hole through which we will thread the threads and stick to the surface of the ball. When the ball is completely covered with ropes, and only small gaps remain, leave the product for a day so that it dries.

The next day, the ball is pierced with a needle so that it deflates or bursts. Circle the circumference of the ceiling with a felt-tip pen on the surface of the circle, then make a cut right size. The hole is needed to insert the cartridge and connect the lamp. The cartridge is well fixed with glue and additional threads.

Bedroom paper lamp

To make a beautiful table lamp from thick paper in the style of Minimalism, you will need:

lamp kit or lantern;
adhesive solution;
putty;
dye;
thick cardboard to create a template;
scissors;
artistic tapes;
grinding block;
wooden weight;
construction knife or drill;
ruler.

Cardboard room lamp

First you need to reprint the template or simply transfer it to paper, while each triangular shape should have 6 pieces from each 6-gon.

Manufacturing technology:

If you have an inspiration, be sure to make a lamp with your own hands - the product can be made from any materials at hand. The video tutorial below shows how to make a designer wood lamp using drawings and diagrams.

A handmade table lamp can become a highlight of the interior, dilute the overall atmosphere and make it more comfortable. Diversity various styles and types of table lamps will allow you to choose the most suitable option.

Using a table lamp is very good for creating additional lighting in a room. In addition, there are situations when the overhead light cannot be turned on or simply does not want to, in which case a table lamp saves. It fits perfectly into the children's room as a night light so that children are not afraid to fall asleep at night in total darkness. In the office, its use is simply necessary, it significantly increases the convenience of reading documents, additionally illuminating work surface. In the interior of the living room, such a lamp will give the room an atmosphere of comfort, moreover, an interestingly designed lamp can become a kind of decoration.

Table lamps can vary in shape, style and purpose. These parameters can be so diverse that it is quite difficult to single out a few. In addition, in the modern world, designers strive for innovation, so they try to mix different styles and shapes, developing something unique and extraordinary. This approach to creating a table lamp can also be used in its independent manufacture.

When choosing a table lamp, pay attention Special attention to the light source. It should not be too bright or dim. The best choice in this case there will be a golden mean. In this case, the probability of pain in the eyes will be equal to zero.

How to make a table lamp with your own hands?

A beautiful table lamp is obtained from wood and veneer. Despite the ease and simplicity of execution, such a lamp looks very interesting and attracts attention.

Materials and tools for self-manufacturing of the lamp

For a lamp, you can make a beautiful and unique lampshade with your own hands.

Manufacturing process

Before starting, you should transfer the layout of the drawing to the base of the lamp, i.e. draw all the lines on a square segment of the tree. Designate places for installing bars, veneer sheets and the light bulb itself. You should also mark with diagonal lines where the holes will be;
It is not necessary to drill the base through, it is enough for 0.5 of the thickness of the wooden piece. Next, you need to drill each of the bars and insert dowels into the resulting holes. In the center of the stand, make a hole equal to the diameter of the light bulb socket so that it sits tightly in it and does not hang out;
To make holes for placing the veneer, we make small cuts in the bars and stand using a disk-shaped nozzle. It is important to make cuts not over the entire area of \u200b\u200bthe base, but only from one hole to another;
A hole for the wire is made on the base quite deep so that it completely closes there. It is better to make it also wide, so that later there is an opportunity to use fasteners;
On this stage worth spending Finishing work. Sand all elements, paint if necessary, and varnish;
At the end, we begin assembling all the parts of the lamp. First you need to glue the bars and let them dry, here you can install a light bulb and place the cord. Then, when everything is dry, insert the veneer plates between the bars.

Using this table lamp manufacturing scheme, you can modify its shape, color and texture. The whiter the veneer, the brighter the light will be, and vice versa. Instead of veneer, you can use other materials for playing with shadows.

Based on the style features of table lamps, and applying tips for making it yourself, you can create unusual lamps, turning your fantasies into reality. The main thing is not to be afraid to use at first glance completely incompatible materials and experiment.

Unusual handmade glass bottle table lamp. The process is easy and understandable to absolutely everyone, regardless of the practical skills of manufacturing such products.

Decorating the house yourself favorite hobby many hostesses, this article reveals how to make a lamp with your own hands. You can revive the interior of a living room, bedroom or hallway with the help of improvised means, only by changing the ceiling of a chandelier, floor lamp or table lamp. Do-it-yourself lampshades for lamps can be used not only in a residential interior, but also in the halls of cafes, pubs, pizzerias.

The choice of materials and lamps for the lamp

Products made for children's rooms should be made from natural non-toxic materials and painted with ecological paints.

When making, you should also keep in mind fire safety, therefore lampshades made of combustible materials made of paper, plastic, feathers or thread should only be used with lamps that have a low heating temperature.

Need to use LED or fluorescent lamps. They have a number of advantages:

long term operation;
minimum heating of the base from the glass part;
light has three shades: warm, cold, neutral.

In addition, such lamps are also called energy-saving, their only drawback is their high cost.

It is also desirable that the connection of the wire to the base be made by a specialist. Do not try to perform this operation yourself, as this may lead to undesirable consequences. It is more convenient to decorate an existing ceiling frame or make it from durable and not very heavy materials.

Used to make lamps the following materials: scissors, mounting knife, fishing line, wire, pliers, hot gun, in some cases it can be replaced with super glue. They should be used by an adult, it is unacceptable to involve a child in gluing. Since in one case he will get a burn, and in the other he can glue his fingers or stick to the details of the future product.

What can you make a plafond from?

Many craftsmen make lamps from completely waste materials:

from plastic or glass bottles;
newspapers, thin or colored paper;
artificial or natural threads;
dried branches of an unusual shape;
disposable spoons;
old disks.

plastic lamp

From plastic containers of different sizes, a homemade chandelier is easily obtained.

For the base, you need to take a bottle of 5 liters. The bottom is cut off. Then circles with a diameter of 1.5 cm are drawn on the surface. They must be cut with a mounting knife or small scissors.
The bottom is cut off from the bottles for decor and the entire surface is cut with scissors into strips 0.5 - 1 cm wide, then the workpiece is heated over the lit burner. Under the influence of heat, the stripes will take on a chaotic appearance.
Then blanks are inserted into a 5-liter container with holes, and lids are screwed on the inside. Then a wire is threaded through the large neck and a ceiling is installed. For such a ceiling, you need to use an energy-saving lamp.
In some interiors, you can find a fancy lamp made on the basis of an ordinary hanger or a straw hat. In general, nothing can limit the scope of the imagination of both home craftsmen and professional designers.

Plafond from glass bottles

Very interesting option homemade chandelier is obtained from glass bottles. They are used to decorate the halls of catering establishments. Also this a good option for the kitchen in a residential building or apartment. This can be a ceiling, consisting of one or more bottles, in which the bottom is cut off. You can do this yourself, but it is better to use the services of a workshop where glass and mirrors are cut.

How to use thread

For a lampshade made of threads or ribbons, you will need: a ready-made frame made of strong wire, threads of different colors, scissors, glue.

The frame consists of two rings interconnected by metal segments. It can be made independently from durable wire.
One color or several shades of thread is required.
A thread is fixed on the lower part, then it must be pulled through the upper ring, lowered down and thrown over the lower ring. It is necessary to ensure that the thread is taut and the coils fit snugly together. As soon as the thread ends, you need to attach to bottom ring next cut.
Carefully cut off the rest of the threads and glue them on the back.

Spoons for the lamp

You can make a multi-tiered, colored lamp from ordinary disposable spoons.

It is necessary to make a wire frame, for a small round lamp you need to make three circles with a diameter of 12, 18, 26 cm. Then the circles are fastened together with a fishing line. The largest diameter will be at the top, there should be the same distance between them.
In spoons, you need to make a small hole with a thick needle at the top of the handle.
Spoons stain acrylic paints in three colors, for example, yellow, orange, red.
Assembling a homemade chandelier: the fishing line is cut into a length equal to the distance between the circles. A spoon is tied to one end of the fishing line, and the other to the frame. Spoons need to be tied to the lower circle of small diameter yellow color, to the middle - orange and to the top - red.

Lightweight and sleek shade

For a paper ceiling, paper or thin cardboard is suitable. Such a ceiling can be either rectangular or square. First you need to consider the size of the ceiling, the larger the room, the wider the design can be. In a small nursery or hallway, a ceiling with a diameter of 30 - 35 centimeters will look good.

The frame can be made of wire, it will consist of an upper and lower part, consider the manufacture of a cylinder-shaped ceiling.

It is necessary to make two circles of wire of the desired diameter. They are interconnected with a fishing line, the distance between the lower and upper frame is 12 - 15 cm, the hoops are fastened with a fishing line in three or four places. How larger diameter grounds, the more to do connecting elements.
On a paper blank, you can draw circles of different diameters, figures of cartoon characters. Outline drawings can be taken from the Internet and printed, then redrawn with carbon paper. A special ruler is suitable for drawing circles, or you can outline caps or buttons of different diameters. Some drawings are cut out completely with a clerical knife, some are cut along the contour.
The paper is tried on the base and glued with an overlap. Then glued to the wire, can also be fixed with a thin wire. To do this, first make a hole in the paper with a thick needle or awl, then thread the wire and carefully tie it to the frame. It is advisable to glue thin paper, as it is easy to ruin it.

Exclusive ceiling made of metal cans

Basins made of any metal are used, an interesting option will be obtained from copper or aluminum containers. An old, used basin will also work. If there is a through hole in it, it must be welded or sealed, for example, epoxy resin.
inner surface needs to be dyed light color to reflect as much light as possible.
The outer surface can be painted in a dark, saturated color, in harmony with the interior.
A fringe about 5 centimeters long is glued to the bottom of the rim with hot glue. In the central part of the basin, it is necessary to make a hole for the wire. It can be drilled with a drill or pierced with a nail.

Such a ceiling can be decorated with a mosaic of CDs. To do this, the discs are cut with sharp scissors into small fragments, which are glued onto outer surface pelvis. You can glue only the bottom contour, and paint the rest. Or decorate the entire surface of the ceiling with such a mosaic. The more convex the surface, the smaller the disk fragments should be.

natural materials

The original lamp can be made from a dry branch of an unusual shape. It must be cleaned of bark and covered with stain, then, if desired, treated with transparent varnish. The branch must be attached to a hook on the ceiling with a regular fishing line. Then I wind the wire with the lamp several times onto the branch. A branch entwined with several wires looks beautiful.

You can make a lamp out of plastic hangers. Detailed in the video:

Lamps in different rooms

DIY bottle chandeliers are more suitable for the kitchen. Designs made of glass or plastic will be easy to clean from dust and wash if necessary. For the kitchen, hallway or living room, a lamp made of natural wood.

For a children's room, a ceiling made of painted plastic bottles, a floor lamp made of bright threads or a paper composition. The latter option cannot be called durable, but this option will appeal to children. Girls will like the plafond with butterflies, plant elements, boys will like designs with cars, superheroes or bright plastic plafonds.

In some cafes, pubs, they are used to decorate the hall original lamps from bottles. It could be beer bottles. They can serve as both a lamp shade and an interesting frame for a lamp.

Ideas for homemade lamps by location

With your own hands you can give a new look floor lamp. You can decorate the ceiling with fabric, threads, paper with cut-out patterns, and you also do not need to ignore the base and leg of the lamp. They can be painted with acrylics, glazed, decorated with beads. The decor of the lower part of the floor lamp should overlap with the elements in the upper part. The easiest option is to decorate the ceiling of a solid color with lace or guipure.

Decoration of lamps

The lower part of the plafond of threads can be decorated with pompoms of the same size hanging on a thread. They are glued on the inside of the frame with glue. Pompoms can hang at the same or at different heights. They can be made in one color or combined in several shades.

To decorate paper lamps, you can use lace, thick tulle, beads of different sizes. Decorate glass jars or bottles can be glass pebbles, which can be purchased at hardware stores. You can also use buttons of different sizes and colors. Small buttons can be glued even on PVA.

On New Year's holidays, it is customary to decorate the Christmas tree, but you can also decorate the shades of lamps, floor lamps. Here you can use the usual rain, do-it-yourself snowflakes, Christmas tree figurines, decorative balls and an ordinary garland. If an energy-saving lamp is installed in a wall or floor lamp, then its ceiling can be decorated with paper snowflakes.

wall sconces installed in living rooms, bedrooms, nurseries. After repair, you can use old sconces only by changing them appearance. You can paint the body of the lamp in a light color, and apply bronze or silver paint on top with a hard bristle brush to create a patina effect. If the ceiling is glass, the pattern you like is applied to its surface using a glass stencil. Here you can use contour (they are used to create a stained-glass window) or spray paints.

Original table lamps unusual products with a design that catches the eye and highlights the interior, making it more cozy as well as interesting. But homemade devices may well have the same characteristics.

They are quite simple to make from improvised materials, decorate to your liking, and the design will be unique. If you plan to use a rather laborious manufacturing technology, it is better to take a master class as a basis.

Glass bottle design

Homemade table lamps of this kind are made using a wine bottle. From the materials you will also need masking tape. A drill will be used in the work, and as an original idea for a light source, you can use Christmas garland with small bulbs (LED). The glass of the bottle should be dark enough to protect from the bright radiation of the light source.

Master class on making a table lamp:

The bottom of the bottle is carefully wrapped with masking tape, it is better to make multilayer glass protection so that it does not crack when drilling.
You need to work with a wet drill, and the drilling speed should not be maximum. On the adhesive tape that covers the bottom of the bottle, a mark is made in the center. There will be a hole through which the garland will pass in the future.
To homemade lamp did not pose a danger, the edges of the hole are processed sandpaper. To do this, you can wrap it around a pencil.
On last step a garland is stretched inside the bottle, and this should be done as evenly as possible.

Exist various ideas how to decorate such a lamp, and a master class for their implementation. For example, you can make a bottle painting. Another original version– use of scrap materials, such as crocheted cover for the glass case lighting device.

soft toy lamp

To implement such an idea, you need to use schemes and master classes. The basis of a soft toy is a pattern. The type of materials used is selected any, at its discretion.

However, it is recommended to pay attention to such features: not too thin or dense fabric. Alternatively, linen. You can crochet all the elements of the scheme. The main thing is that in this case the knitting should be openwork, not too tight.

First, all available parts are sewn together, the base of the toy lamp remains open. Filler is stuffed inside. Then it is recommended to treat the fabric or crocheted toy with a special compound that is used to compact the fabric.

Soft toy night light

The product should dry well (1 day). Next, the filler is removed, which is easy to do with a pencil wrapped with double-sided tape.

At the bottom you need to cut a small hole for the output of the wire and place the LEDs

The bottom edge of the product is trimmed so that the base is as even as possible. A small hole is cut out on the side for convenient location of the cord. An LED cord is laid inside a crocheted or sewn toy.

Lamp made from a flower pot

Another master class allows you to create a lighting fixture from improvised materials that most users will probably find: a flower pot or a ceramic vase.

You will need a flower pot or ceramic vase.

Useful in work: a wire connector, a cartridge, a metal threaded tube, the length of which slightly exceeds the height of the pot. You will also need plaster and a spatula. To install a threaded rod, you will need a disc and two nuts. The last elements will fix the disk. This side of the bar falls to the bottom of the vase.

Attach the disk and washer to one end of the threaded pipe

In order for the home-made lamp to be stable and durable, a gypsum mortar is laid out at the bottom of the flowerpot, which must be prepared in accordance with the manufacturer's recommendations.

Gypsum dries very quickly, which means that you need to act quickly and accurately. Before pouring, a rod with a disk should already be installed at the bottom of the vase.

A sufficient thickness of the layer of gypsum mortar is up to 1/4 of the height of the flowerpot. Complete hardening of gypsum occurs within an hour.

Leave the disk at the bottom, and pour the plaster into the pot.

Next, a current collector is attached to the cartridge. It remains only to install the lampshade. If desired, you can buy it in the store, however, there are more original ideas: crocheted lampshade, fabric, etc. The power cable runs through the top edge of the vase.

Attach the lampshade to the top of the chuck

To hide it, the lampshade should be at or slightly below the edge of the flowerpot. It is recommended to choose the materials of the lampshade according to the shade and style of the lamp base, as well as taking into account the interior design.

The more transparent material is used (crocheting, fabric, etc.), the more intense the lighting from the lamp will be. To make a lampshade, you will need a ready-made frame from an old lighting device, and a home-made analogue - made of wire - will also be used.