Garden benches. How to make a bench: original ideas (drawings, photo reports) Original benches

Good afternoon, today we will make a variety of benches with our own hands. I have collected in this article all the EASIEST WAYS make it convenient and a beautiful bench. I will give detailed explanations and illustrative photographs, and will tell you as clearly as possible about how to make a bench made of wood(timbers and boards) and scrap materials(pallets, old chairs, boxes, etc.). I will also provide drawings, assembly diagrams, and step-by-step workshops.

All assembled models I will lay out the country benches according to their complexity - that is, we will start with the simplest and most concise methods - and end with real professional products worthy of the hand of a master. After this article, you will feel that you have become the same master who knows a lot about his craft and can easily make a bench from absolutely any material, even if it is not much. And the bench will stand firmly on its legs and serve your family for years. And who knows, maybe you can even sell your benches to your neighbors - after all, they will also want to have them country benches on your site. And later you will start doing the same according to my article-lessons.

In this article, as well as in the next articles in this series, we will look at...

1. Benches made from old chairs.
2. French-style chaise longue bench
3. Beautiful benches made from bed headboards.
4. Master class on an elite bench from a chest of drawers.
5. Country benches with backrest - made of timber and foam blocks.
6. Benches for summer cottages - panel supported on a solid sidewall.
7. Simple drawing benches from edged boards- in 15 minutes.
8. Country benches with a curved side part.
9. Slatted benches for a summer residence - with a curved seat shape.
10. Timber benches with backrest and armrests – 23 models.
11. Benches under a canopy or a classic pergola.

So, let's figure it out. And let's start with the EASIEST WAYS to make a country bench with your own hands.

Model No. 1

Bench for a summer residence

FROM OLD CHAIRS.

In the photo below we see an original and very simple bench - which can be easily made with your own hands from unnecessary chairs. Everyone at their dacha has old, shabby chairs. Once upon a time you left one chair in the rain, the varnish coating on them was swollen, the soft upholstery had long ago crumbled into shaggy holes. It’s a shame to throw it away; you put it against the wall of the garage or in a shed - and it continues to deteriorate. Then another chair was added to it - but it’s still nothing, and you keep it on the summer veranda. And sometimes you see shabby chairs with lopsided legs at the entrance (someone took them to the trash).

All these old robbers can be given a new brave life. Paint them a bold, rich color. And cover with a wide board - screw it on with self-tapping screws (so that they hold on to the leaky bottom of the chair; it can be reinforced with a wooden overlay). Or screw it not to the bottom but to the frame of the chair.

By the way, if you don’t have old chairs, IT’S NOT A TROUBLE. Go to any flea market website - many of them sell old chairs for mere pennies. They are happy that they sold it. You are lucky that you found it.

If wooden chairs have different seat heights, this can easily be solved by filing the legs of high chairs (or stuffing additional thick boards onto the seat frame of a low chair to raise the seat to the desired height.)

Chairs can be connected not only in the seat area, but also along their backs. Here on step-by-step master class making such a bench (photo below) we see how it is done:

• The attachment points along the rear line of the seat are a long wooden strip.
• The fastening points along the front line of the seat are fastened with screws (or simply a butt, which is held in place by the fact that the back bar prevents the chairs from moving apart).

We adjust the side rails of the bench. We cut it out corner groove on the handrail so that it fits into the frame of the back of the chair.

We sand the varnish coating from the chairs (preparing them for painting). We prime before painting - a special primer for wood. We impregnate with a moisture-resistant coating.

And attention – we add elements of strength. From below and above between the backs of the chairs we nail short wooden holder strips. They will combine the backs of the chairs into a single common back of a country bench.

Cut out the board for the seat. Please note that special square cuts are made in it (so that the high “humps” of the chair legs pass through them.

This is how we get an elegant garden bench. It can be placed on the garden lawn in a place with a table - under a canopy, in a recreation area, on a veranda or terrace. And for the winter and rainy season, bring it into the house.

But here is an idea of ​​how we can arrange the chairs DIFFERENTLY under our future bench at the dacha - WITH ROUNDING.

You can also make a round garden bench around your favorite tree or lilac bush in your dacha - also from chairs placed in a circle with their backs.

Even if you found only 2 chairs at a flea market, you can still make an original bench with them - which only you will have.

Moreover, there is still one exclusive idea hidden here - just for TWO chairs.

In the photo below we see exactly how you can make an elegant one out of two old chairs with your own hands. French bench-chaise.

In the photo diagram below we see a master class - where it is shown how two backs of chairs become the side elements of the frame of a garden bench.

• First we do rectangular seat frame(light wood in the photo below) - also scientifically it is called TSARGI (frame elements under the seat of a chair, or under the table top). We nail this drawer frame to the lower slats of the chair back.
• And then, so that our bench does not wobble back and forth, we make an additional screed frame already in the lower part of the legs of the future chaise lounge. Scientifically, such a frame-screed at the bottom of the legs is called a FOOT FRAME.
• We paint the entire product in White color and we get a solid French bench for a beautiful holiday in the country.

If desired, you can attach a backrest to such a garden chaise bench. Simply nail the boards to the side of the chair frame. How this was done is shown in the photo below.

Model No. 2

Country benches

FROM AN OLD BED.

Here are ways to create a beautiful bench for your garden using the backs of an old bed.

One back is sawn in half as is. The halves will be used as side elements of a country bench.

Even if the headboard of your bed is not made of a solid board, but is decorated with carved balusters, you can still make a bench according to this design.

The seat can be covered in one piece wooden shield. Or upholster it with slats as in the photo below.

The second headboard can be used under the FOOT part of the bench– from the front edge. How this was done is shown in the photo below. The bottom frame of the bench can simply be paved with edged planed boards and painted. Or you can cut out a solid shield and place it on top of the frame.

You can use only one backrest to create a bench.

You can make a FRESH FRAME for a country bench from an edged board.

Or the frame for the seat - the bench frame - can be taken from the same material as the bed frame. How this was done is shown in the photo below.

And pay attention. Here part of the bed frame is PADDED ON TOP - to increase the level of the seat.

A beautiful country bench can be made even using modules from any other furniture. For example, from an old buffet. Let's say you have a buffet, part of which cannot be restored (drunken guests fell and broke the line of drawers).

Then fate itself tells you to make an exclusive bench out of it. It's unusual to beat the rest of the buffet. And create a cozy corner for family privacy.

And you won’t want to expose such a designer bench to the rain. You will find it a place of honor in your country house. And sew blue pillows for her with embroidery of snow-white patterns.

Model No. 3

SHIELD garden benches

WITH YOUR OWN HANDS.

To immediately explain the term “panelboard”, I’ll show you this: simple design– mini-shop made from cutting kitchen boards. This is the classic panel design of a bench. That is, the product is ASSEMBLED FROM SOLID SHIELDS.

In the photo below, the boards are connected using a groove method. The seat board fits into the grooves on the stand legs.

Here below the bench is made EXACTLY THE SAME - using the panel method. Only the material of the shield is rougher and unhewn. And here they added a back - it was also cut into grooves cut into the support panels.

• The fastening of the shields to each other can be GROOVED (as in the photo above) - where in some shields grooves are cut out, and other shields are moving down. Such fasteners are used only in panels made from a SINGLE PIECE OF WOOD. Glued boards are not suitable for this - they can delaminate in the places where they are glued.
• ADDITIONAL FASTENING ELEMENTS are also used for fastening – wooden(tsars, corner jibs, pro-legs), metal(angles, staples and perforated plates).

Village benches are made using the panel method. 2 side panels (these are the legs) - connected to each other by a long board (these are the legs). The board can be located in the lower part of the interleg, or in the upper part of the interleg - immediately under the seat board. In the photo below we see both of these methods of positioning the leg under the bench.

As you understand, the shields you work with do not have to have a name correct form. These may be fragments of an old gnawed board - in which you cut flat support lines for SEAT AND BACK REST.

In the photo below, the solid shield acts as a support for both the seat board and the back board.

The principle is the same here - a solid support for the seat and back of a country bench.

And this beautiful white bench for the dacha is made according to the same principle. Only it is made from evenly cut boards and painted.

Below we see a panel model of a bench with a back, where 2 panels play the role of support for the seat and back.

And these supporting SIDE PANELS are made at a slight angle of inclination. And so the bench turned out to have a seat with an inward slope and a slightly reclined back. It is very comfortable to sit on such a bench.

And agree to do it, cutting out such a bench with your own hands is very easy. Here the drawing does not have to be accurate. Just do it to your heart's content. Easy side angle choose by eye.

• The side support of the backrest is in the form of a long triangle (choose the angle of inclination yourself).
• The leg support for the seat is in the form of an elongated trapezoid (can be tilted or not).
• A piece of thick timber is smoothed under the leg supports so that the bench has height. But if you have a wide board, then the legs will be higher on the bench, then you can do it without timber supports

All parts can be mounted on ordinary nails.

So that the bench isn't so low(if you wish) you can make the foot beams higher - knock together several pieces of timber at once - put them on top of each other like a tower and secure them with inside with a board (to keep everything together) or without a board just on nails.

And such a bench can also be PUT ON LEGS - also in the shape of an elongated trapezoid. The pads are stuffed on the inside of the seat support.

BENCH SHIELDS may be KNOWN (that is, not solid, but consisting of boards connected to each other with a bridge). The simple country bench with the photo below demonstrates this method.

And this garden bench from thick boards is also made according to the same principle.

Model No. 4

Benches FROM EDGED BOARDS

Make it with your own hands for the dacha.

And here's another simple model country bench. It is simple not only in design, but also in material. From one long edged board you can make a garden bench like this quickly and easily with your own hands.

It can be supplemented with armrests, covered with a noble dark stain, or painted with a bright rich color.

On the sides of this type of country bench you can make stands for books, beer, those things with which you like to relax in the country.

Let's look at the drawing of this country bench. We see that all the corners of the board scraps have an inclination of 30 or 60 degrees. Dimensions in the drawing are in inches. One inch is equal to 2.54 cm.

We see the drawing from the side. The length of the back and seat is your choice.

We cut the board into the pieces we need. And we assemble the bench using bolts, screws or nails.

You can also make a table for provisions with such a bench at the dacha. Or a regular shield shop.

Model No. 5

Panel benches for summer cottages

WITH CURVED SIDE SHIELD.

The shields that you cut for the SIDEWALLS of your bench at the dacha can have SMOOTH ROUNDED LINES. Then the bench can become a real work of art - your creative work.

The seat in such a bench is supported by STRAPS padded underneath it on the inside of the sidewalls.

The back rests at the bottom - on the same bar as the seat, and at the top on a bar padded vertically along the back part of the curved sides.

The boards from which you cut out the figured sidewall can be processed along the edge, giving it roundness and smoothness (left photo below).

You can also cut out the curly sides not from an ordinary shield, and from carpentry with relief - the front part of a cabinet or an old paneled door. You don’t even have to remove the door handle - but leave it for beauty (in the right photo of the bench below).

Model No. 6

Slatted bench for a summer residence

How to do it yourself.

You can also make an interesting SLATT BENCH from the carved sides. They have a round seat with smooth outlines and a curved back line.

In the photo below we see just such a bench, convenient for a summer residence.

The curvature of the bench is obtained due to the fact that narrow slats are stuffed along the CURVING PERIMETER of the shaped side parts.

In the photo below we see a master class on making such a bench for a summer house. To ensure that the slats do not sag under the weight of a sitting person, another frame figured element is made for such a bench - in the center. All three parts are connected together into one common frame - simply by FITTING THEM ON THE SLOTS OF THE BOTTOM RACKS (as in the photo below).

And then on this frame along its upper perimeter we put slats on the screws.

If you want such a bench to be longer, then you just need to make not three figured models of the frame - but four, or five, or six. And of course, the padded slats should also be long.

Model No. 7

Quick bench –

from foam blocks with a cavity.

Foam blocks (or gas silicate blocks) are sometimes made with through holes inside. This is done to save material and also to enhance the heat-shielding properties of such a building material.

And we can use this “leaky” feature of gas silicate blocks - for the good purposes of creating a bench for the dacha.

To do this, we install 2 two rows of foam blocks WITH THE HOLES DOWN, and on top we put more foam blocks WITH THE HOLES TO THE SIDE. And we insert timber of a suitable cross-section into these holes. To make it more comfortable for your butt to sit on top, you can place foam pillows. It is better to choose those that are lined with waterproof fabric. Or sew it yourself from oilcloth and thick foam rubber (sold in hardware stores and construction stores).

You can simply hammer the planks into a solid one to create a flat seat without holes.

It’s also good to coat the foam blocks with regular paint to create a bright, beautiful bench.

Here are some ideas for making country benches with your own hands. But these are not all the models of wooden benches that I would like to tell you about. Therefore, wait for the continuation - we will make interesting benches from wood (timber, boards and logs).

Your professional growth will not end here...

You will see how easy and quick it is to make a real structure with your own hands - a large summerhouse. How to install poles, how to make a roof yourself (without any construction education), how to cover it with a roof (polycarbonate, slate, tiles). Stay with our “Family Bunch” - and we will give you “golden hands”.

Good luck with your dacha construction.

Olga Klishevskaya, especially for the site

If did you like this article
And you want to thank our free author for this painstaking work,
then you can send any amount convenient for you
on his personal YaD wallet - 410012568032614

According to the classic, everything in a person should be beautiful. This also applies to everything that surrounds us. Creating comfort in your country house, don’t forget about the garden plot. A smooth lawn or flower beds serve as decoration for your garden, it doesn’t matter at all, the main thing is that there is a place where to sit and relax from the bustle of the city and household chores. A DIY garden bench is a great opportunity to add individuality to your country cottage area. Let's look at a few interesting options handmade benches and figure out how to make some of them.

The simplicity of the design and the availability of materials allows even a novice craftsman to decide to create such an interior element. The best material Wood or stone will be used to create a garden bench. They fit perfectly into the design personal plot and create a feeling of unity with nature. It is possible to create a bench from scrap materials. Surely a zealous owner will have a couple of outdated wooden chairs that can be put to use.

Whatever you decide to make a bench from, the first thing you will need in any case is a design project, and the necessary drawings and assembly diagram for it. Drawings of garden benches for every taste can be found on the Internet, but if you wish, you can develop them yourself; after all, we all received the primary skills of creating them in school, and the design of a bench is not so complicated.

1. height - about 40-50 cm;
2. seat width - on average 55 cm;
3. back height - 30-50 cm;
4. the height of the armrests from the seat is 15-20 cm.

These are the dimensions that will allow you to sit comfortably on the bench.

DIY wooden bench

Let's first consider the option of a simple wooden bench.

Below is an approximate drawing of such a bench for a do-it-yourself garden. Its most complex element is the slightly concave seat. The dimensions of the elements depend on the final dimensions of the bench. We offer the following sizes of individual elements:

• seat boards – 25x100x1200 mm (4 pcs.);
• legs - 100x100x440 mm (4 pcs.);
• front upper drawers – 25x100x1200 mm (2 pcs.);
• front lower drawers – 25x100x1200 mm (2 pcs.);
• seat board supports – 25x100x400 mm (6 pcs.).

Prepare everything necessary tools and materials and you can start. You will need:

• suitable boards and timber for making the seat and legs of the bench;
• jigsaw;
• sander;
• self-tapping screws;
• screwdriver;
• antiseptic for wood processing;
• stain;

Operating procedure:

1. First of all, cut out all the necessary parts according to the list with a jigsaw.

Pay special attention to preparing the seat supports. Before cutting, make appropriate markings to simplify the task.

1. Sections need to be processed sandpaper for protection against splinters.
2. When the parts are ready, carefully treat them with an antiseptic to protect the wood from destruction and insects. This will extend the life of the product.
3. Start assembly by attaching the seat supports to the upper frames according to the diagram.

Advice! Make all connections with self-tapping screws. The connection with nails is short-lived, it quickly becomes loose, and such a bench will lose stability.

1. Attach the seat boards to the resulting frame, deepening the screw heads.

1. Lastly, attach the legs, securing them with the lower drawers for strength.

1. The already assembled bench can be covered with stain. This product will help give the wood the noble look of a more expensive material and emphasize its structure.

This DIY bench is made from natural material will decorate any garden and will not create a dent in your wallet.

Bench with wooden back

A bench with a back is undoubtedly a more convenient option than a bench. And don’t think that making one yourself is more difficult. You can, for example, create a bench with a backrest with your own hands in an ethno style from a solid log.

For the seat of such a bench you just need to cut a log. The second part of the log can be used to make bench legs. These parts are connected to each other using metal pins.

First, holes are made in the fastening areas, the diameter of which is slightly less than the diameter of the pin. First, the pin is driven with a sledgehammer into one part to about half the height, then the second part is pushed on top.

Advice! Before hitting the material with a sledgehammer, place an unnecessary piece of board on top, this will prevent damage to the surface of the material.

The back of such a bench can be made from a log of smaller diameter. To fasten the backrest, you can use metal elements or, if not available, take wooden ones.

Don't forget to treat the wood with a protective antiseptic.

Bench - swing

The garden bench can also be made in the form of a swing. This option is especially relevant if you have children, they will obviously like it.

Have you decided to make a swing with your own hands? Except ordinary materials to make a bench and a bench you will need a durable fastening material, such as rope or chain, as well as metal chains and carabiners. The swing can be decorated with colorful pillows made, if possible, from moisture-resistant materials.

Shop - sandbox

Another bench option that will definitely make your children happy is a sandbox with a lid.

A very convenient option that will fit into a country house landscape design, will not take up much space, will appeal to children and adults. Approximate dimensions: 1.20x1.45x0.3 m.

When making such a sandbox bench, you can rest assured that country cats will not get to the sand, and the ubiquitous magpies will not steal small toys.

Bench - flowerbed

Lovers of wild blooms surround themselves with flowers everywhere. For them, we can recommend making a bench - a flowerbed.

Even a novice master can work on such a bench. It is necessary to build a wooden floor between two boxes. It’s simpler - there’s just nowhere. The boxes are filled with soil and your favorite plants are planted there. A green corner made in this way will decorate any summer cottage.

Benches from scrap materials

To create a designer bench, it is not at all necessary to purchase material, even inexpensive ones. You can make an excellent bench from scrap materials. For example, old wooden chairs.

To create such a simple but very elegant bench, assemble a frame from a 50x30 mm beam of the same length as the seat of your bench should be. For two people 120 mm is enough. Attach the backs of the chairs to it as in the picture. For fastenings, use long self-tapping screws.

Paint the structure created in this way in the color you need.

To make the seat, you can use a sheet of plywood, fiberboard or wood furniture board. Cut the seat slightly wider than the frame. If desired, it can be covered with batting or foam rubber and upholstery fabric or leather substitute. A furniture stapler is very useful for covering the material.

The bench is ready! All that remains is to find a suitable place for it and enjoy the result.

Another handy material for quick creation construction pallets can act as benches.

If you have the appropriate tools, it will not be difficult to assemble a bench of any design from them. The main thing is to carefully treat the pallet boards with sandpaper and an antiseptic protective agent (this rule works for all wooden products planned for use on outdoors). In addition, such a bench can be painted in your favorite color or covered wooden elements stain. You can decorate it with simple jute rope and metal rivets, as well as pillows of various sizes and colors and textures.

As you can see, a garden bench made by yourself is not only a place to sit. It is enough to show a little imagination and a corner for relaxation with the whole family is ready. Made by you yourself, it will save money and time on searching. suitable option, which sometimes you simply cannot find. If you do not have sufficient carpentry skills, create a bench from scrap materials; it does not require much labor, but it looks no less aesthetically pleasing.

How to make a garden bench with your own hands from wood. Video instruction.

You can relax calmly in the shade of trees in the summer or bask in the sun on a cool autumn day on a wooden bench that you installed in the garden yourself. IN modern design garden furniture is one of the full-fledged elements of landscape design.

Taking into account the decorative value of garden benches made of wood, you should try to choose a model that will harmoniously fit into environment. For a young garden or summer cottage without big trees It is better to choose light furniture options with decorative thin metal legs, simple benches and benches that are laconic in shape. If the garden is old and well-groomed, then seats in the Provence style are suitable - stylized as antique furniture with wooden decor.

I can decorate an overgrown summer cottage with an imitation of a wild natural thicket with benches assembled with my own hands from natural material- driftwood, driftwood, lightly processed branches. A bench made of logs hewn with an ax would look very good in such a garden. Such seats should be installed in places hidden from view: among flowering bushes or around a bend in a path.

When choosing a place to install a bench for a summer house, you need to pay attention to the views that will open to the eyes of those sitting on it.

It is not advisable to place the bench in such a way as to contemplate an unsightly fence or compost heap. Place it near a pond or flower bed, under a branchy old tree.

Then your relaxation will be complemented by the pleasure of the smell of flowers and the play of light on the water, the rustle of leaves and coolness in the shade.

Various types of benches can be installed on the veranda near the house, in the relaxation area by the pool or outdoor fireplace. They will also find use under a canopy in the garden. In each case, you must adhere to general rules compatibility wooden product With general style plot. How to make original benches from pallets, watch this video:

As a material for garden furniture wood is traditionally chosen - an easy-to-process material that allows you to bring almost any idea to life. Currently, along with regular board and as a block, you can use moisture-resistant varieties of thick plywood. Made from durable and aesthetically pleasing sheet material you can assemble designs that are suitable for modern designer landscapes and for an ordinary courtyard that does not have certain style characteristics.

If wooden benches are made in a stationary version, then care should be taken to protect them from moisture. A variety of impregnations and paints and varnishes. Outdoor furniture will have to be coated with paint or varnish every 1 to 2 years as the protective layer wears out. Such measures can significantly extend the life of a wooden structure.

How to build benches yourself?

In order to build a comfortable bench with your own hands, you need to make a sketch of it. Exist optimal sizes garden furniture, which must be observed in this case:

• seat height above the floor - 40 - 50 cm;
• width (depth) of the bench - 50 - 55 cm;
• The height of the backrest above the bench is 35 - 50 cm.

These dimensions allow a person of average height to sit comfortably, lean on the back, and stand up easily. If the owner’s build differs greatly from the average, then the dimensions of the bench will have to be selected individually. The backrest is usually made with a slight tilt back. For more information about wooden benches, watch this video:

To work with wood you will need the following tools:

• hacksaw or jigsaw;
• drill and screws, or hammer and nails;
• roulette;
• pencil.

To assemble products of complex shapes, wood glue can be useful. It is used to fasten parts that are connected using the tongue-and-groove method or with a furniture dowel. For plywood products, long metal threaded studs and nuts are useful.

A simple bench for a vegetable garden or bathhouse

The simplest wooden bench Even a novice master can do it with his own hands. Such benches can be seen in abundance at the gates of village courtyards; they can be placed near the beds, in a bathhouse or utility room. They are not distinguished by their sophistication and decorativeness, but they can perform the functions of garden furniture quite successfully. To make a bench you will need a board 2 - 2.5 cm thick and about 20 cm wide.

Benches for a bathhouse or vegetable garden are easy to make

According to the drawing in Fig. 1. you need to cut out the following parts:

• seat - 1 piece;
• apron - 2 parts, the length of each is 10 cm shorter than the seat;
• legs - 2 parts.

File off the corners on one side of each apron piece as shown in the diagram. Measure 2 - 2.5 cm from the edges of the element for the legs on each side in the upper part, cut a groove 10 cm long. If desired, cut out holes for the handles on the bench seat. To learn how to make a bench with your own hands, watch this useful video:

Assemble the product in the following sequence:

1. Drill holes for self-tapping screws in the plane of the apron board at a distance of 10 cm from each end. Place the board in the groove on the leg parts and screw the screws through the holes into the edge of the board. Attach the 2nd leg pattern to the other side of the apron.
2. Repeat all steps and attach the apron to the other side of the bench base.
3. At a distance of 15 cm from each end of the seat, make several holes in the plane of the board. Place the part on top of the base and attach it with self-tapping screws, screwing them into the end of the leg part. For strength, you can make additional holes along the length of each side of the seat and attach it to the apron boards.

Treat the surface of the product with coarse emery cloth to remove hangnails. If necessary, paint the bench to your taste.

Simple bench with backrest

Another simplest project shown in Fig. 2. To make a bench with a backrest with your own hands, you will need 2 pieces of logs about 25 cm long, boards for the back and seat, and 5x5 cm bars for the backrest posts. If you want the seat to be a little higher, you can take 4 pieces of logs or timber and lay them on top of each other, fastening them with dowels.

The back is screwed on with self-tapping screws on the reverse side

Making the bench is very simple. To ensure that there are no nuts or nail heads on the surface of the product, fasten the parts using dowels and glue. The back can be screwed with self-tapping screws wrong side so that they don't drill right through the board.

To make dowels, you need wooden rounded rods (a thin handle is suitable for garden tools). Drill 2 holes in the log with a diameter equal to the thickness of the dowel. Based on their location, make corresponding recesses in the underside of the seat. The work must be done very carefully so that during assembly you do not have to adjust parts of the bench. For more information on making a bench with a back, watch this video:

Lubricate a piece of wood for the dowel with glue and insert it into the hole on the log so that a small fragment remains outside. Its length should be equal to the depth of the recess drilled in the seat (Fig. 3). Lubricate the dowels with wood glue and place the board on them. Do the same with another piece of log.

Cut off the bars required length for the manufacture of backrests. Screw it to the ends of the logs with self-tapping screws. Drill 2 holes in the upper part for attaching the backrest. The distance between the holes should be less than the width of the board. Screw the screws through the holes into the board. The finished bench can be painted or coated with clear varnish.

Stylish bench with backrest

Making garden furniture according to the proposed project is not difficult at all. The basis of the structure is slabs of porcelain stoneware or concrete and boards 2 - 2.5 cm thick. If desired, heavy materials can be replaced light plywood the same thickness. A wooden bench with a back will be mobile.

Stylish bench has an interesting backrest

The following parts will be required:

• squares 50x50 cm for legs (plywood or board) - 12 pcs.;
• boards or plywood rectangles 15x200 cm - 5 pcs.;
• backrest supports 15x65 cm - 4 pcs.;
• crossbars 15x17.5 cm - 2 pcs.;
• threaded rod M16 55 cm - 4 pcs.;
• nuts and washers M16 - 8 pcs.;
• self-tapping screws

The plywood will first have to be cut into fragments of the required shape and size. If boards and slabs are used, this step can be skipped. To learn how to make an original bench with your own hands, watch this video:

Drill 2 holes at an equal distance from the edges in the upper part of the square parts of the legs. Adjusting the long parts of the seat as in the diagram (Fig. 4), make 2 holes in them on each side. Screw a nut onto one end of each rod and put on a washer. Alternating long and square elements, assemble the bench. Tighten the nuts on the other side of the studs.

This bench can be used without a backrest.

But for convenience, you can do it too. To do this, fix 4 boards 15 x 65 cm with self-tapping screws from the inside of the back of the bench. Glue crossbars between them or place them on dowels.

Decorative benches made from natural materials

Untreated wood is an excellent material for garden furniture. The bench, similar to the throne of a forest king, fits perfectly into the landscape, imitating wild nature. Such seats are very appropriate near rockeries or old trees with a spreading crown in an overgrown corner of the garden. Rustic benches go well with picnic areas trimmed with wild stones or barbecues made of sandstone and boulders. Original shop in this video:

The simplest option for sitting from logs is a monastery bench. To make it, a raw log needs to be sawn in half lengthwise. Legs are made from short sections, laying them cut down on the ground. Long halves of logs are secured to dowels from above, cut side up. To prevent the bench from staining your clothes, it is better to choose logs hardwood and dry them well before assembling the furniture.

To remove splinters and burrs, the cut plane must be planed smoothly with a plane and treated with emery cloth.

A complicated version of such furniture is a bench made of logs, supplemented with a backrest with your own hands (Fig. 5). To attach the backrest, you need wooden or metal supports and a crossbar. These parts can be made from thick wood branches, timber, or steel strips. Fastening is carried out using self-tapping screws of sufficient length or nails.

Examples of original wooden benches

A log bench can be made in another way (Fig. 6). The photo clearly shows the grooves in the upper part of a thick log sawn in half. You need to insert a board at least 4 cm thick or a beautiful cut of a tree trunk into the grooves. If desired, an exclusive piece of furniture made by yourself can be supplemented with a backrest. The supports for it need to be attached to the inside of the legs on flat surface. The crossbar can be a thick branch or the same cut of wood as for the seat.

Chopped table with benches

A set of table and benches will be convenient at the dacha in the dining area or near the barbecue (Fig. 7). It’s not difficult to make one if you know the basic techniques for making wooden log houses. To begin with, 2 logs of approximately equal thickness are placed on the ground. With an ax you need to cut out semicircular recesses (bowls) at the ends of the logs. The size of the bowls will depend on the diameter of the log that is chosen for the seats. This trunk needs to be sawn lengthwise. An example of chopped furniture in this video:

In the middle of the 2 lower logs, you need to cut out 1 more cup to install the transverse support. It may not be a very thick log. Its length should be such that the ends protrude beyond side surfaces trunks.

For the table base you need shorter logs. Their length is approximately equal to the desired width of the tabletop.

In the middle of each trunk, you need to cut out recesses that are suitable in size to the thickness of the crossbar. Lay the parts of the log house with the cups down, covering the transverse log with them. Make a tabletop from the boards and secure it with nails. Place the halves of logs in the places designated for them.

How to make benches from branches or driftwood?

Exactly this creative activity. Having found beautiful driftwood and polished driftwood trunks in the forest or on the shore of a pond, you can make furniture amazing beauty(Fig. 8). Each such bench is unique, because it is difficult to find 2 identical branches. Therefore, there can be many solutions for how to make a bench from driftwood.

The main thing for all such products is one thing - the parts are adjusted directly on the spot to fit the already finished legs, seats, and backs. The branches should intertwine harmoniously, forming a structure that will support the weight of an adult. To connect non-standard parts, you can use both self-tapping screws and nails. The most reliable connection is with dowels and glue. Where a tight fit of the pieces of the structure is desired, driftwood can be trimmed with an ax.

The most original benches can be made from branches and driftwood

Such decorative benches can even be used to decorate rooms in a chalet or rustic style. They go well with wild stone trim. They will look harmonious in the garden among flowering bushes or near a pond.

The variety of models of benches that you can make with your own hands from wood is limitless.

The main thing in making furniture from wood is the careful fit of parts.

Then ready product It will turn out neat, without distortions. Treated with moisture-proof impregnations and coated with varnish or paint, any garden seat will last for many years.

To garden plot was quite comfortable, it should be properly equipped. An important component is garden benches. You can make them yourself different ways and from various materials.

Bench made of concrete slabs and boards with backrest

By looking at the drawings of the bench, you can find out the features of its structure. You can make such a design with your own hands relatively easily, quickly and without high financial costs.

Making a bench with a backrest with your own hands is described in great detail in step-by-step instructions.

Assembly: initial stage

After the preparatory work, it’s time to process the wood. In order for a hand-made bench with a back to serve for a long time and decorate the area, the materials must be pre-treated.

The tree is covered antiseptic compounds and let it dry. After this you can start collecting backrests

On one of the two-meter boards, fifty centimeters are measured from the edges. At this level the edges of the beton slabs. From this mark another fifteen centimeters are measured towards the center of the board. This is where the first boards will be attached. From the resulting marks we measure seventeen and a half centimeters - the gap between the back boards. Next, we measure fifteen centimeters for two more boards. There should be a gap of five centimeters between them. All this can be seen in the drawing.

Wood glue is applied to fifteen centimeter sections. They are attached to boards, the length of which is sixty-five centimeters. Additionally, they are secured with self-tapping screws.

On top, between the boards of the back, pieces of seventeen and a half centimeters are glued. To ensure that the parts stick together well, they are clamped and held until the glue sets. After gluing is completed, the back is covered with an antiseptic.

All wooden parts can be covered varnish. This will give them additional stability and attractiveness.

Assembly of the main part

It is better to assemble the main part of the bench from both sides. Concrete slabs are placed between the boards, and drilled holes insert threaded rods M16 fifty-five centimeters long. You will need four of them.

The rods are fastened with M16 nuts and washers. They are twisted simultaneously from different sides to make the bench level.

Simple DIY bench

You can make benches for your garden with your own hands quite quickly if you follow the instructions. Let's consider four options for such garden structures.

On drawings benches, all its features are indicated in detail. Making such a bench with your own hands is quite simple. The only one complex element is a concave seat.

The number of parts and their dimensions are indicated in the table.

We begin making a bench with our own hands from wood with blanks necessary details. Boards and beams are cut into pieces of the required length.

Making seat supports will be somewhat more difficult. You will need to mark the blanks. Two points are marked along the edges at a distance of seven and a half centimeters from the bottom side, and in the center a point at a distance of four and a half centimeters. They are connected using a flexible plastic ruler and cut out jigsaw. The sections are processed with sandpaper.

The seat supports are attached to the two upper drawers. One on each edge and one in the middle. Next, screw in the supports, spaced from the outer ones by the width of the leg. All connections are made with self-tapping screws.

Boards are attached to the resulting base seats. It is advisable to deepen the screw caps.

Then attach legs. They are attached to the seat supports. The lower drawers help secure the legs.

The finished product is coated antiseptic and varnish.

Simple bench No. 2

To make such a garden bench with your own hands, you will need concrete flower girls and boards. Flower girls are required to create the base of the bench. Use two with a rectangular base and two cubic ones.

To make the base stable, the flower boxes must be glued or connected from the inside with staples secured with self-tapping screws. The container is filled with a layer of drainage and soil. This increases their stability.

The seat for the bench is made of boards. To do this, they are cut into pieces of the required length. These blanks are laid so that there is a distance of half a centimeter between them. They are then connected using cross bars. The planks are placed in three places: at the edges and in the middle. Corners are attached to the slats. With their help, the seat will be secured to the flower girls.

DIY bench with backrest

Prepare the bench parts shown in the figure. They are being processed antiseptics before connecting.

Then the parts are assembled into supports. The corners are first rounded and chamfered. First, parts A and B are connected with a bolt, and then B, C and D are also connected using a bolt.

The inclination of the backrest is determined by part D, after which it is connected to part A. Similarly, but in a mirror image, another support is made.

After this, the back and seat are assembled. To do this, the supports are placed so that there is a distance of one meter and twenty centimeters between them. First, the front and rear strips are screwed to the supports, then all the rest, and finally the stops are screwed in.

On last stage The back of this bench is screwed on.

Bench No. 4Another option for a simple DIY bench. Its length is one hundred twenty centimeters. The height from the ground to the seat is fifty centimeters, the height of the backrest is also fifty centimeters.

The base is made from boards, the thickness of which is five centimeters and the width from ten to twelve. One of the legs continues and serves as a support for the back. The supports are connected using the “half-tree” method and secured with bolts.

The basis for the seat is a block secured with self-tapping screws. The short supports on the back of the bench are connected with a collet to increase stability. The seat and back are covered with boards of less thickness. The surface is painted or varnished.

A simple bench with a back for a summer cottage

The dimensions of the structure and wooden parts can be seen on drawings benches. If we consider how to make a bench with your own hands, then this option will prove to be the most optimal in terms of the simplicity of the process and the result obtained.

It is better to purchase materials already cut to size. If this is not an option, then you need to cut them yourself.

The resulting blanks polished. The ends of the boards are processed with an electric planer.

The back legs of this simple DIY bench also support the backrest. To create required level tilt, the workpieces are marked.

At a height of forty centimeters, mark the attachment point seats. Above, the board is cut at an angle of twenty degrees. The cuts on the two workpieces must be identical.

First they collect legs benches: the front ones are connected to the back ones using a beam. It is better to do this from above and below.

When the side parts are assembled, they can be connected to each other with seat boards. Screw the boards with self-tapping screws, leaving a distance of one or two centimeters.

To strengthen the structure and increase its stability, make the lower harness timber along the legs. Two boards are attached for the back.

Finish the work with finishing coated, which will protect the product from moisture and adverse conditions.

DIY pallet bench

Make a bench with your own hands from pallets It’s not difficult if you use your imagination. To do this you will need three or four of these wooden structures. Some will need to be sawed to obtain additional parts. The simplest DIY bench design is made from pallets, when two pallets are attached perpendicular to each other, creating a back and seat.

To prevent the design from becoming too bulky, it is better to cut the pallets according the right sizes. The elements are fastened with self-tapping screws. Add side parts to enhance strength and make legs. All this can be seen in the photo.

Since the material of the pallets is untreated and rough, it will be required first polish. This will allow you to avoid splinters.

The manufacture of a bench with your own hands from pallets is completed by coating it with varnish or paint.

Bench puzzle

You can make such a bench with your own hands if you have a wide board and cuttings for shovels. Curly seats are cut out of the board in the form of puzzle pieces. Legs made from cuttings for shovels are attached to them. The result is separate stools that quickly assemble into one long bench. All manufacturing stages are discussed in detail in step-by-step photos.

Benches from unnecessary chairs: two DIY options

First option

To create such a bench for your dacha with your own hands, you will need four old chair.

From the first two chairs remove parts from the front of the seat.

The remaining sawed off the front legs are slightly lower than the seat structure.

From the resulting parts you need take off old varnish or paint. To do this, apply to the parts special remedy, dissolving paint coatings. Then the softened layer can be removed with a spatula.

The racks should drill holes for dowels. Holes are required on the front and end sides.

The dowels are lubricated with glue and inserted into the drilled holes.

When the dowels are glued, you can assemble base benches. To make the structure durable, the parts are fastened with self-tapping screws. Surface of the structure sanded.

For seats benches choose a board that is suitable in size, saw off the excess.

If several narrower boards are used, they are glued together with wood glue. For a tight connection, they are clamped with clamps and wait for the glue to dry.

The finished seat is also glued to the base with wood glue. Heavy objects are placed on the board and clamped together with the base with clamps.

When the glue has dried, cover the seat with masking tape and paint paint the remaining structural elements for wood.

The tape is removed and the seat is treated stain. Finally, the entire bench is varnished.

Second option

To make a second garden bench with your own hands from old furniture you will need two chairs. It is better if the back and hind legs are not separated.

Two identical chairs clean up all parts of the structure except the rear legs with the back.

They take bars five centimeters wide and three centimeters thick. Cut two parts equal in length to the width of the chairs, and two pieces of the same length as the finished bench. A rectangle is assembled from these four parts. It is secured to the backs of chairs with self-tapping screws.

Another frame is assembled in the same way. Several transverse strips are attached to it. This design is attached under the seat, makes the bench more reliable and acts as a shelf.

If the chairs have old covering, then remove it with sandpaper. After this, the surface is puttied with a special compound or coated with a primer. When the layer has dried, it must be sanded with fine-grained sandpaper. Finally, the structure is coated with paint.

The seat for the garden bench is made by hand from Chipboard or plywood. A rectangle is cut out of the selected material, which is half a centimeter larger than the base on each side. Then cut out a piece foam rubber with the same dimensions. A rectangle is cut out from upholstery fabric. It should be five centimeters larger than the seat on each side.

Foam rubber is placed on a sheet of plywood and covered with fabric on top. The fabric is attached from the inside out to the furniture stapler.

The seat is attached to the base with a piano hinge.

Bench-swing

To make such a bench for your dacha with your own hands, you should prepare necessary materials. Manufacturing begins with creation basics designs. The seat bars are attached to the back bars at the selected angle.

Additional ones are installed along the seat ribs, providing rigidity.

Attached to the seat planks, drilling holes for fastening in the base bars. The same goes for the back.

Armrests are installed on both sides of the seat. They can be secured with bolts.

The resulting bench cover wood protection products and varnish. It is very important to paint everything as carefully as possible.

The bottom of the bench is reinforced with metal profile. Chains are attached to the profile on which the swing bench will be suspended. It is imperative to check the reliability of the beams on which the bench will be suspended.

Log bench

To make such a bench with your own hands from wood you will need chainsaw. The main material is a thick log one meter long.

Log mark, so that you get two slightly unequal parts. The smaller one will be used to make the backrest, and the larger one will be used to make the seat.

Chainsaw log sawed along the mark. The resulting irregularities are immediately cut off with the same saw.

The cut triangular piece is cut into pieces and inserted into the holes in the seat. The back is secured on top. The bench is almost ready. All that remains is to give it a more decorative look.

Can the seat be placed on legs. To do this, recesses are made in the lower part to install a pair of logs as legs.

Transformable bench

The design features of the transformer can be seen in the drawings of the bench. A transformer bench is made with your own hands from planed boards, which is sawn to the specified dimensions.

Sliced timber parts holes for fasteners are drilled.

At the table top, the boards located on the edge can be made wavy.

In material intended for countertops, drill holes with a diameter of twenty-two millimeters and a depth of three centimeters. Cuttings of the same diameter will be inserted into them.

The edges of parts and edges are processed and rounded.

All elements are assembled using screws and screws. Screws are needed with dimensions 6x70 and 6x90, screws - 8x80.

Wooden parts are painted stain.

The structural parts that will move are connected by hinges.

Parts of a round shape are placed between the boards of the tabletop. cuttings

Install a stop for backrests

A hand-made transformer bench is covered varnish.

Rocking bench

Making an original bench with a backrest with your own hands is not difficult if you have the tools and materials. First you need to consider the drawings of the bench, which do not contain a large number of details.

The side parts according to the pattern are transferred to Europlywood three centimeters thick. They are cut out using a jigsaw and the ends are processed with a grinder.

To attach the connecting strips, markings are made. Then the holes are drilled. After assembling the frame, the slats are attached using self-tapping screws. The fastening points are sprayed, and the entire product is varnished.

Bench around a tree

The simplest version of such a bench is hexagonal The size depends on the size of the tree. Measurements are taken at the height of the seat. A margin of fifteen to twenty centimeters is added to the result obtained. If you divide the result by 1.75, you will get the length of the inner side.

To cut boards ten centimeters wide, they are laid in four rows with intervals of one centimeter.

The cutting location is marked immediately for all rows with an angle of thirty degrees. So cut out six sets of blanks.

Legs are used with a height of sixty to seventy centimeters. They are connected by cross members by drilling holes and using bolts and nuts.

The seat is installed so that the joints are located in the center of the ribs of the legs. The outer parts are screwed on first, and then the inner ones. In this way, the entire hexagonal structure around the tree is assembled.

Finally, the back is made and the apron is installed. The result is a DIY circular bench with a backrest.

The finished product is processed oil impregnation.

Bench made of curved branches

A bench made of curved branches will look original. It will require branches for the front part, two legs, a horizontal top and a pair of transverse branches.

Sawing branches so that they fit each other as accurately as possible. Next they are connected by metal corners.

The back part is made in the same way and connected to the front.

The finished product is placed on a flat surface and the seat is assembled.

Bench options

• Log bench, which blends well with the surrounding nature. It consists of half a log used for a seat and two short round logs, which are the legs.
  
• Beautiful wooden bench with a back and armrests, reminiscent of a sofa. Curved and cut elements make it more attractive, while leaving knots and irregularities gives the structure a natural look.
  
• Bench made of wood and metal. The base of the structure is metal. The wooden parts of the seat and back are attached to it. The thin metal parts make it look lightweight.
  
• The bench has a simple, classic shape. It is made of wooden, rather wide boards. This width allows you to sit comfortably on the bench. Armrests make the design more complete.
  
• Original bench made of wood with figured details. This option is well suited for a site with a natural, rural design. Carved legs and armrests, a figured back - all this gives the product originality.
  
• Bench with an interestingly shaped back. The curved parts gradually bend back, creating a unique design. The seat is slightly curved but has a more traditional appearance.
  
• Wooden complex- a table with two benches. The design looks traditional due to the material used. An original solution is the fastening of all components into a single structure.
  
• The bench is made of solid logs. A single piece is cut out of it, combining the back and seat. The legs are attached to the bottom. The log required is quite large.
  
• Bench with storage box for toys. Outwardly it looks like an ordinary wooden bench-sofa, but under the seat there is a drawer in which you can put various things.
  
• A comfortable bench made of wood with a simple shape. The base is made in the form of a rectangular box. The back is also simple with a straight shape. Placed on the seat soft pillows, providing additional comfort.
  
• Wooden bench located around a tree. It is made as if it consists of four benches, each of which has one armrest. The composition looks attractive and comfortable.
  
• A simple bench made of wide boards. It looks solid, but its size is somewhat hidden due to the gaps between the boards and the light blue color in which it is painted.
  

Each personal plot should have several benches and benches with backs so that you can good weather relax outside, sit under the gentle sun and just take a break from working in the garden. You can buy such a wooden one or metal bench, or you can just do it yourself. In this article we will look at what types of benches there are and how you can make one of them yourself, having all the necessary tools and materials at hand.

How are there species?

There are a large number of benches with a back and each owner country house or a dacha chooses for himself the option that is most suitable for the exterior of his personal plot.

Benches come in a variety of varieties depending on their scope of application.

• Ordinary benches with a back are suitable for any personal plot and will fit perfectly into the exterior of the yard. They are comfortable and very practical, as they have a simple design and are unpretentious in appearance. Suitable for installation near the house, in a gazebo, near a pond, etc. They can be made of wood, metal, stone, and also be combined (wood and metal, wood and stone, wood and brick, plastic and other building materials).
• Corner benches will look great where you can’t put a regular large bench with a back. They can be placed in the corners of the gazebo, in gardens, as well as in any convenient location on a personal plot. Such benches can be metal, wooden, stone or combined.
• Ordinary benches without a back can be installed anywhere, as they are universal and convenient enough for any country house. They can be easily made with your own hands, since they are made according to the most common standard drawing of the classical type.
• Oval, round or semicircular benches with and without a back will look great in the center of the same round gazebo, in the center of the garden or in another place where they will create an aesthetic exterior for the entire garden plot, as well as perform their direct functions. Also in the center of a round bench a tree, green bush, or blossom can grow beautiful flower bed or even a children's sandbox. Here everything depends on the imagination of the master and the functional needs of the owners of a country house or dacha. They can be made of wood, metal, stone, as well as in a combined form from various compatible friend with a friend of natural materials.

Photo gallery: do-it-yourself garden benches with a wooden back - types and designs

Wooden bench with metal legs for the garden Wooden bench with forged metal legs for the garden Corner wooden bench with brick support Semicircular wooden bench on a brick support Shop from wooden beam garden with backrest Decorative wooden bench for the garden with supports made from flower boxes Classic wooden garden bench with handrails and backrest Round wooden bench with back for the garden Original bench made from solid logs for the garden Wooden bench on supports made of natural stones for personal plot Wooden bench with concrete supports in the form of flower beds Wooden bench with wooden supports in the form of flower beds Wooden bench with wicker back for the garden Stone designer bench for the garden Square wooden benches for the garden

Preparatory stage: drawings, dimensions, angle of inclination

Before you start making a bench for your personal plot from any type of material, you need to take all measurements and draw up exact drawing future design. This is necessary so that it turns out smooth without distortions and rolls. Also, the design diagram will help to calculate required amount material for making benches of any type.

For the manufacture of wooden structures For a personal plot, pine, oak, birch boards or logs are usually used, as well as pear, hornbeam and durable larch. Almost any tree is easy to process, has excellent decorative qualities, and also fits aesthetically into the countryside landscape. The main advantage of wood is its beautiful aesthetic appearance. But meanwhile, it negatively tolerates exposure to sunlight, high humidity and low temperatures (severe frosts). Therefore, it is best to install wooden benches in closed gazebos, on terraces covered with awnings or make them portable (collapsible) so that they can be put away in an enclosed space (pantry, basement, closet) for the winter.

Steel supports will be the most competent choice for making a bench with a wooden seat and back to place it on the territory of a summer house or country house. This bench will serve you for at least 15 years, and you will not need to remove it during snow or rain.

How to make a wooden bench with a backrest with your own hands

To set up a wooden bench we will need:

Before you start making a wooden portable bench, you need to cut the boards into certain elements:

1. All prepared boards must be sanded, all side parts smoothed and thoroughly soaked with antiseptic. Then leave until completely dry.
2. We mark the height of the bench at 40 cm. Starting from the very middle at the top of the elements of the longest legs that will hold the back, you need to make an oblique cut at a slight angle of about 20°. Then all the corners of the bars must be cut down and sanded on both sides. In this case, the back will have an inclined shape. The cuts must be strictly identical, otherwise the bench will end up skewed and have an unattractive appearance, and it will be uncomfortable to sit on.
3. Assembling the bench legs. The distance between the legs should be about 28 cm. Front (facade) and rear wooden pairs benches for support on the invisible inner side must be fastened using prepared bars and self-tapping screws. We connect the legs with a beam, which we cut to cover the entire width of the structure - 50 cm. It is best to do a double strapping - top and bottom.
4. In order to protect self-tapping screws and screws from premature corrosion, it is necessary to pre-drill the necessary holes and recess their heads slightly into the board.
5. On the frame of the bench, as shown in the drawing, we nail or screw the planks at certain intervals (1 or 2 cm). Three planks will be used for the seat and two planks for the back. After all the elements are filled, it is necessary to check with a level the correctness and evenness of the entire structure. For greater reliability, stability and rigidity, the legs at the bottom are secured with strips on both sides. It is advisable to leave gaps of several centimeters between the slats for better air circulation and drainage. We attach the backrest (the first bar) at a distance of 20 cm from the seat, and the second - at a distance of 38 cm from the seat.
6. The structure of the bench needs to be strengthened and for this it is necessary to bottom trim legs To do this, we take two beams 1.5 meters long and screw them to the front and rear legs of the bench frame.

Bench decoration

After completing all carpentry work, the bench must be completely treated with fire retardant and then covered with waterproof varnish in several layers or regular oil paint.

If you want to make the bench more aesthetically pleasing and designer-friendly, you can simply saw the boards lengthwise and then stuff them diagonally, crosswise or in a herringbone pattern.

Making a garden bench from wood and metal

A bench with a back, a wooden seat and durable metal legs will the best option garden furniture that can be installed in your garden plot. This design can be left outside without any problems even in winter.

Material calculation and necessary tools

To make a bench we will need:

• One iron corner with a shelf measuring 40 - 50 mm;
• One beam for making a bench seat 40 mm thick;
• Special bolts;
• Hacksaw or grinder;
• Drill;
• Screwdriver;
• Electric or gas welding machine;
• Sandpaper or sanding machine.

Step-by-step instruction

1. The metal corner must be cut into four pieces of one meter each to make vertical supports for the structure. Cut five pieces of half a meter and two pieces of one and a half meters to make a frame for installing a seat and back boards on it.
2. To make the back and seat, we cut seven strips of timber, 1.5 meters long and 10 cm wide. We sand them and smooth all the side parts well. We soak all the boards well with an antiseptic and leave until completely dry.
3. We cut the ends of the joining parts from the iron corners exactly at an angle of 45° and then connect them in series using hot welding. First, we make a frame for the seat and weld the iron legs well for the subsequent attachment of the backrest to them, as well as the stops. During the welding process it is necessary to use protective equipment.
4. In the boards of the seat and back, where the fastenings will be located, it is necessary to drill holes for special bolts. After welding work metal structure It is necessary to sand well at the seams in order to eliminate all irregularities and bumps. Then treat the metal with a special anti-corrosion coating and oil paint in two layers.
5. We bolt the finished back and seat boards to the finished metal frame. We first impregnate the boards with a fire retardant (preferably saline) and then cover them with a good layer of water-repellent varnish or colored paint.
6. It is necessary to make markings on the ground for the legs. To do this, you need to dig four holes about 50 cm deep and pour river sand (about 10 cm) on the bottom, and fine gravel (about 20 cm) on top. We lay pieces of roofing felt on top and put reinforcement mesh. We install the bench legs into the holes and check the horizontal evenness of the structure with a level. Then fill the legs with concrete (ratio of sand and cement 3:1).
7. If you plan to place the bench on a regular asphalt or paved surface, then you do not need to make a concrete foundation. The legs of the structure are made from four pieces of iron angle, about half a meter long. For greater stability to the bottom of the corners, it is necessary to weld square “heels” or strengthen the entire structure using a lower metal frame.

Finishing

All metal structural elements must be treated with anti-corrosion agents and primed. Then paint with regular oil paint.

We impregnate the wooden elements with special antifungal agents and fire retardants, and then paint them with waterproof varnish or colored oil paint.

If desired, the metal parts of the bench can be decorated with various forged iron patterns, which you can forge yourself or purchase ready-made from special companies.

Bench for a personal plot on brick supports

Material calculation and tools

To make a bench we will need:

• Construction brick;
• Wooden boards (thickness about 40 mm);
• A pack of self-tapping screws and self-tapping screws;
• Several bags of cement, fine sifted sand (6 bags or more) and gravel.

Step by Step Actions

On stone-paved and concrete areas, the bench must be placed on cement foundation. On soft ground it will be necessary to make a columnar foundation.

1. We mark the area for the installation of brick racks and remove upper layer soil (turf). We dig holes with a diameter of 20x20 cm and a depth of about 50 - 60 cm to construct the foundation. At the very bottom of the well we pour sand 10 cm thick and on top crushed stone 20 cm thick. We compact all this well, water it a little and leave it for a day.
2. We put several pieces of roofing felt on top and place a bundle of five reinforcing rods in the hole. We fill it all with concrete and let it harden for about three or four days. To mix concrete, we take cement, sand and fine gravel (1:3:5).
3. We place a small layer of liquid concrete (1–2 centimeters) on the prepared foundation. This will be the basis for the future brick decorative base. Next, we begin to lay the brick with the dressing. The masonry is made to the width necessary for the structure, that is, the same as the bench itself or a little narrower. The height of the brickwork should be about 50 cm. Inside the masonry on the top row we leave space to form a shelf for the subsequent installation of a bench seat.
4. We fasten the seat boards together using boards and self-tapping screws. Then we install the finished bench on the prepared brick supports. We impregnate the wood with fire retardant, let it dry and cover it with a special water-repellent varnish or colored paint.
5. Also, depending on how long the bench will be, you will need to make several brick supports. Corner or shaped (semicircular, round, oval) structures are best installed on a solid brick base, which will be located on a strip-type foundation.

Bench decoration

We treat all wooden planks with antifungal agents and fire retardants, and then prime and cover them with waterproof varnish or regular oil paint. Brickwork does not need additional finishing, as in itself it looks quite beautiful and aesthetically pleasing. If you still want to make it a different color, you can also paint it with oil paint.

Video: how to make a bench for a country house yourself

If you make a bench out of wood and metal with your own hands, you will be able to enjoy the fruits of your labor for many years and relax on it in the shade fruit trees. With proper and timely care for such wooden bench with metal or brick supports will serve for many years. But in order to prevent it from being damaged by heavy rains or snow in winter or autumn, it is best to put it indoors, if possible. Regular care can significantly extend the life of your bench in your garden.