Variants of interior openings. Doorway without a door: necessity or design decision? How to arrange a doorway: photo

Entrance door trim

Sometimes combining the space of adjacent rooms is the most optimal planning solution. The reason for this is both the banal lack of space, in which every square of living space counts, and considerations of the aesthetic perception of the interior.

And then, if we judge purely practically: the door is far from always needed - so why spend money on buying it. It is much easier, in accordance with the concept of the style of interior decoration, to frame the doorways with stucco molding or veneer them with wooden planks.

If you just take and remove the door from the hinges, the bare box in the opening will not look good. The half-loops and the reciprocal level of the lock will be an eyesore and break the harmony in the interior. To avoid this, an opening in which there is no door can and should be beautifully lined, after which, as they say, it will become the very “icing on the cake”.

Use of door extensions

The first question that the reader may have is: “Is it necessary to dismantle the door frame when ennobling the opening?”. It can be left, but only in one case - when the opening is improved with wooden extensions, and provided that the old box is installed evenly.

If the tree is worn out, it is better to remove it and level the opening with ordinary planed boards 15-20 mm thick. Their width is selected according to the thickness of the wall. The blank for the horizontal bar is sawn along the width of the opening, and two side posts are cut out along its height, minus the thickness of the crossbar that will rest on their ends.

If the door slopes are uneven, then wooden wedges are inserted under the leveling strips, checking the correct position of their level. The gap formed between the board and the slope surface is filled mounting foam, let it dry, and only then proceed to cutting and installing decorative strips.
Their role is played by extensions used for facing slopes in deep openings that cannot be covered with a box. In our case, they are installed on top of an old box, or a frame from a board, which is done solely for the sake of alignment.

If the opening is even, then, in principle, it is possible to mount extensions directly to the base base. But then they will have to drill holes for dowels, which, no matter how you hide, will be visible. You can use decorative caps, but they are regularly lost, leaving the attachment points in plain sight.

Note! When the extension is mounted to a wooden box, then micro-studs can be used as fasteners, which go into the thickness of the plank and remain almost invisible. But for this you need such a tool, which you see in the photo above.

Cutting and installing extensions is performed similarly to the elements of the leveling frame. Now that you have perfectly even slopes, mounting the cladding on them with your own hands is as easy as shelling pears. The main thing is not to damage the front surface of the decorative strips when cutting.

In addition, it is very important to make high-quality cuts, which is not always possible when working with a hacksaw. It is best to use a miter saw for this purpose. It is simply indispensable in the case when the doorways are framed with stucco molding, which will be discussed in the next chapter.

Framing with polymer molding

Gypsum stucco molding today is used only for decorating rooms in the Rococo, Empire or Renaissance styles - and even then, designers have long interpreted them in a modern way. Working with gypsum is more difficult, and the price of such a finish is higher, so the best alternative to it is polyurethane stucco, made in the best traditions of classical architecture.

Duropolymer vs Polyurethane: What's the Difference?

Relatively recently, such a thing as duropolymer stucco has appeared. What is it, and how does this material differ from polyurethane? And this is a composite that high pressure made from polystyrene. It has a high density - and, accordingly, strength, which compares favorably with polystyrene.

The negative qualities of duropolymer products include a greater weight than polyurethane and a rather meager assortment. The advantage is excellent mechanical strength. This property is doubly valuable when it comes to, because it is clear that in the process of bringing dimensional furniture into the room, there is always a danger of hooking and damaging the decor.

By appearance duropolymer cladding is almost indistinguishable from polyurethane moldings. Such a kit, which you see in the picture above, costs about 3600-3700 rubles. To clad the opening on both sides, two of these sets are required, plus two long and one short inner panels.
Door frames made of polyurethane moldings are usually not sold as a set, but are made up of individual elements according to the customer's taste. It can be a composition of sandrik or cornice, moldings, which in this case play the role of platbands - as well as consoles, rustications and keystones. All details can be selected according to style and size, and alternate them when facing as you like.

To decorate the side surfaces of the slopes, as well as the walls adjacent to the opening, you can use panels that imitate, beautiful bas-reliefs. Importantly, the flexibility of polyurethane products allows you to veneer not only straight, but also spherical surfaces, and in the vast majority, they are used today to design arches.
The selection of stucco cladding for openings allows you to show your imagination - but, of course, this should not be a chaotic set of details. The pattern of the opening needs to be well thought out, correlated with the decoration of the room as a whole, as well as the design of the door panels, if they are nevertheless installed.
Both duropolymer and polyurethane door decor are mounted in the same way: by adhesive method, on a flat, puttied and primed surface. Slope leveling can be done both wet and dry.

For example, if initially there was no opening in the wall, the metal frame, which is made for the purpose of reinforcement, can only be hidden under the plaster. Applied on a steel mesh, in this case it is part of the technology, and is performed even when the walls in the room, and accordingly the openings, are sheathed with drywall (see).

A little about installation

A small instruction presented in this chapter will help you deal with the installation of polyurethane stucco. By and large, there is not much difference where exactly it is installed: on a wall, ceiling or in an opening - the technology will be the same.

So:

Before decorating openings, products must be adapted to environment , so they need a day or two to lie down indoors. Since the installation of the decor is carried out using adhesive, it is very important that the surfaces with which the adhesive will come into contact are clean. Therefore, it is desirable not only to remove dust from them, but also to degrease the back side of the products with a solvent (but not acetone).
Work should be carried out at temperatures above +10 degrees. Installation of stucco decoration is recommended to be carried out before proceeding with the finishing of ceilings and walls. When cutting moldings, it should be borne in mind that it takes about 10 cm of their length to cut corners. In this case, it is also necessary to keep in mind the repetition of the pattern, if any, on the front surface.

When working with polymer stucco, you should have tools such as a level, goniometer, tape measure, furniture stapler, kit rubber spatulas, glue gun, hacksaw, Miter saw, stationery knife. As for consumables, you need to have two types of glue: mounting and docking.
It is very important that the plastered or puttied base on which the stucco molding will be glued dries well. Otherwise, the decor may peel off, which will ruin not only the work, but also the material. On the base base, the products are put on mounting glue, and when joining the decor elements together, they use glue.
Mounting adhesive is applied to the end of the stucco product with a layer about 5 mm thick. The stucco molding should be pressed tightly against the wall, and the excess that has come out should be immediately removed with a spatula. After joining the horizontal and vertical frame elements with glue, they are additionally fixed with metal brackets.

After about a day, but not earlier, it will be necessary to cut off the excess docking adhesive. This is perhaps the most painstaking work. It should be done very carefully, since the joints should not be visible - the appearance of the door frame depends on this. Products made of polyurethane are sold already primed for painting, so that after removing the glue, you can start puttying.

For this purpose, either a special elastic putty is used for finishing polyurethane, or a white adhesive, which, as a “two in one”, can be used both for mounting stucco molding and for finishing joints. After the puttied joints have dried, their surface must be sanded sandpaper with fine powder, remove dust - and you can start painting.

Ensuring the privacy of each family member in big apartment rests with interior doors. If there is a lot of living space, and there is no need to fence the space, you can beautifully equip a doorway without a door. The absence of a door leaf between rooms is enough practical option expansion of space. This is especially true for small apartments. Also, thanks to this solution, you can more conveniently arrange pieces of furniture. Finishing a doorway without a door is definitely a profitable solution. It is worth learning more about the features of its implementation.

Features of doorless openings

This design is equipped in such a way that the door frame is completely eliminated. You also need to choose the size of the opening and its shape. The interior is determined by the design solutions present in the adjacent rooms. If an arched structure is chosen, it is necessary to take into account the height of the ceiling and the location of the load-bearing walls. Photos of doorways without doors can be seen below.

Usually the standard decision that is made in such a situation is a decorative finish using the following materials:

panel plastic;
artificial or natural stone;
polyurethane molding.

As additional decorative elements, you can use curtains and screens. Particularly popular are materials that do not lose their characteristics even after many years of operation.

Advantages of an open door

One of the popular solutions in terms of equipping openings is the device sliding doors. They do not require much space for installation, so they are often mounted in apartments with small dimensions.

Properly designed open openings look quite attractive. They create the effect of combining adjacent rooms. Also, this solution improves the quality of ventilation of the apartment. Such openings also look great if they open onto an insulated balcony.

Thanks to the equipment of the doorless space, it is possible to fully compensate for the standard layout. It's worth the money and effort. to one of distinctive features such openings is to reduce the cost of materials that will be used to design a doorway without a door.

A doorway (for example, to the kitchen), not equipped with a door leaf, is an advantageous solution for the interior. The implementation of various finishes, presented in the photo in the article, is original and emphasizes the individuality of the apartment owners. Work can be done by hand.

Drywall arches

One of the cheapest options for decorating an opening without a door is to use drywall. Material Features:

it can be cut with an ordinary knife;
due to the smooth and even surface of the material, its preparation is carried out in a minimum volume;
the wrong side has a fairly high degree of adhesion with various adhesives;
the service life of such material is 20 years of continuous operation.

To fix the cladding, you will need to install the frame of the arched structure. It is usually made from metal profile. A mounting bar can also be used. First, wall drywall is mounted, and on top - facing.

The use of waterproof putty, as well as special tape allows you to close the seams much faster. When choosing a material, it should be borne in mind that acrylic-based compositions have a fairly high strength. Unlike them, gypsum products are well polished. This property is especially important for paint and varnish processing arches.

Making an opening using plastic

In the process of designing doorless openings, plastic is often used. A variety of panels allows you to choose from many interesting options. Such products can imitate various textures, including wood and stone.

The plastic decoration of the opening without a door is usually selected according to the pattern, as well as the color and texture. This allows you to create an interior in which all the details will look as harmonious as possible. With the right selection of material characteristics, you can visually increase the space.

During the finishing of the opening, it is not required to invite specialists. If you have certain skills in such work, the whole process can be done independently.

Polyurethane molding

Often, polyurethane moldings are used in the design of doorless spaces between adjacent rooms. If the work is carried out in a small apartment, it is better to pay attention to materials that have a low-relief pattern. Volumetric stucco is appropriate only if there are high ceilings.

One of the advantages of polyurethane is the ability to paint it with any paint. For this reason, such a coating is quite often used in the design of openings without doors. The material can be easily fixed with a special adhesive.

Stone in the finishing of openings

Stone is one of the most attractive and durable materials used in interior decoration premises. It has a high degree of wear resistance, and also has a beautiful appearance. It is easy to attach with glue.

Artificial stone loses to natural in terms of service life, but its lightness compensates for this. Also, this finish is inexpensive. There are many models on the construction market. artificial stone in different color schemes.

Stone cladding methods

There are several options for how to lay stone elements when facing an opening. One of the most common is the way to make edging with smooth edges. This cladding looks neat and stylish. The second option is torn edges. Before starting the installation of tiles, all surfaces of the opening should be leveled. To increase adhesion, the surface should be primed.

An interesting variant of clinker cladding. Such products perfectly imitate the old masonry with natural stone. Clinker masonry is characterized by increased wear resistance, as well as the preservation of the original appearance of the material even after years of operation.

How to choose the type of opening

According to the opinions of designers, arched structures have great potential to increase the external attractiveness of the opening. The rooms look more interesting. It is especially worth considering the implementation of an arched doorless opening in the case of narrow corridor. Thanks to this solution, you can improve not only the interior design, but also increase the convenience of moving around the apartment.

If the apartment has standard ceilings, you can make an arch that has a slight rounding. Typically, the radius of such structures is selected based on the size of the doorway. The radius should be twice the width of the free space under the arch.

Important! Sloping arches visually increase the space, raise the ceiling, and can also be combined with many interior styles.

To decorate an opening with a high ceiling, you can use arches of an unconventional shape. For example, they are trapezoidal, elliptical and asymmetric. If, for example, an arch is erected over the space between the corridor and the living room, you can make it in the form of a structure with slopes that mimic half-columns.

Openings made in the Baroque or Empire style look interesting. If the apartment is small, do not overload the space with small elements. This will visually reduce the space.

Many designers pay more attention to symmetrical designs. If you decorate such an opening with low-relief polyurethane stucco, you can get a great look. To complete the arch, you should understand the rules for working with drywall, as well as purchase necessary materials for the frame.

Restrictions

During the arrangement of the opening between the rooms, certain rules of work should be taken into account. There are several limitations that require close attention. For example, block partitions are often installed in apartments, in which the door frame is a power element that supports the wall. In this case, its dismantling may lead to subsidence of the partition and the appearance of cracks. For this reason, such openings are first strengthened.

Such frames provide uniform distribution of the load on the walls. For example, it rises if the opening is trimmed with stone. You should also think about the environmental friendliness of materials. If you buy too cheap products without thinking about their quality, the consequences can be unpleasant.

conclusions

Thus, finishing an opening without a door is a fairly popular method of arranging the space between two rooms. This allows you to add interesting details to the interior, as well as visually enlarge the premises. There is enough a large number of finishing options for openings.

Arched structures are very attractive and can be installed in apartments with any style. However, when choosing this option, it is worth considering the features of the layout of the living space.

Materials for finishing the opening can be very different - polyurethane stucco, stones, clinker tiles, plastic panels. This diversity allows you to choose the most suitable option for your apartment.

Exist various options doorway trim. They help to achieve harmony and stylish design premises. It must be borne in mind that these structures are divided into two types, which depend on the presence or absence of a door leaf. It is this element that determines the sequence of activities carried out in order to obtain the desired effect.

Ways of facing openings without door panels

Finishing a doorway without a door is carried out in two main options:

Standard. This technology provides for lining openings with various materials, without changing the design.
Arched. This method lies in the fact that the configuration of the opening changes - significantly or slightly.

Each of the methods requires compliance with certain rules, as well as accuracy.

Various types of materials for standard finishes

To decorate a doorway without a door, finishing products are used that have different technological features.

PVC panels

This option is one of the most popular. This is facilitated by the fact that such products have excellent characteristics, and are also very affordable. For laying, the method of landing on glue is often used. Panels are mainly faced with slopes. Other parts of the doorway are finished with other materials.

On a note! PVC products require careful selection. To make a coating that will look harmonious in the interior, preference should be given to varieties made as an imitation of natural materials.

Everything is done like this:

Requires to leave the structure for a while to avoid displacement of elements. Now proceed to the elimination of external joints. If they close plastic corners, as is done when facing windows, it may not be a very attractive effect. Therefore, it is better to perform putty with putty. Then you can start the subsequent finishing. For this, painting, wallpapering is carried out.

Should know! Exist plastic architraves, which are well combined with PVC panels. But pruning them is a very laborious task. The fact is that it is necessary to adjust the elements at an angle of 90 degrees.

The best replacement for PVC will be MDF panels. Finishing openings with such material goes well with other products. If it is required to perform cladding of structures in this way, in order to exclude the formation of visible joints, lamination is used.

Facing the door slope with MDF

stucco work

It is immediately worth noting that stucco molding is currently used, which is made of polyurethane. Unlike gypsum options, this type of product is characterized by low weight. Its installation can be performed without the involvement of additional assistants. An important feature such a material is that it lends itself to post-processing. That is, it is easy to paint in different colors.

Finishing the opening is carried out according to a certain scheme:

All parts and glue are preliminarily kept in the room where the installation will be carried out for 24 hours. This will ensure that all elements get used to the existing microclimate.
The areas to be pasted over are carefully covered with a primer. Only compositions that have a deep penetrating effect are selected.
Important! It should be remembered that the stucco sticker is done first. Only after that, it is possible to produce a general wall decoration.
The surfaces of the products are slightly rubbed with sandpaper. Next, glue is applied. It is evenly distributed on the wrong side of the fragments. Now the stucco is applied to the selected area and pressed well. To prevent the elements from slipping, small self-tapping screws are screwed under them.
If excess glue appears, then they are immediately removed. When this cannot be done immediately, then you can use acetone, which is moistened with a sponge.
An important point is the docking of elements. It can be carried out at a right angle (perpendicular installation), or trimming is performed, which is done at an angle of 45 degrees.
After cladding, joints appear. They are hidden with putty, which, after drying, is rubbed with sandpaper. Particular care should be taken when finishing between rooms, because it is required to provide for the location of parts on both sides.

Ennobling the doorway with stucco provides some nuances. This option is best suited for rooms that have fairly high ceilings. If applied to small rooms, then it is advisable to carefully consider the location of all elements. The fact is that it is easy enough to overload the room so that the interior becomes simply spoiled.

Fake diamond

The use of artificial stone is perfect solution, which helps to decorate a doorway without a door in a very stylish and modern way. This option is superior to similar products due to the fact that the material is produced in a large decorative range. For example, clinker tiles are also used for cladding such structures, but their choice is rather limited.

On a note! It should be borne in mind that the concept of "artificial" does not belittle the merits of this product. The simulation is carried out with excellent accuracy. The texture and shades of natural stones are repeated.

Finishing the doorway with artificial stone

Before finishing decorative stone doorway without a door, you should familiarize yourself with its advantages. There are the following advantages of the material:

Excellent appearance, which brings presentability to the interior.
Possibility of combination with other finishing materials.
Excellent mechanical resistance.
Durability. Service life is calculated in decades.

For work, small-sized products are used, which have some relief. If you choose a deeper texture, it will look very cumbersome.

The cladding is done according to various technologies. Often laying is carried out in a way that allows you to form uneven edges.

On a note! Currently, special elements have been developed that act as corner plates. They help you avoid overcutting.

Making the opening is quite simple:

Marking is carried out on the selected areas. It should repeat the developed scheme. To carry out this process most accurately, the stone is laid out on the floor in a given order.
Wall surfaces are treated with primers that have deep penetration. This will improve adhesion. It is important to allow all areas to dry thoroughly.
Fixation can be carried out on a special adhesive for tiles or "liquid nails". The second option is suitable for those cases where the base has almost perfect evenness.
The composition is applied to the wrong side of the elements. It is important to remove any excess.
The stone is laid in ways that make it possible to form a seam or get by with a monolithic surface (without joints).
Details are seated in place and pressed. It is important to achieve a good grip.
If joints have been formed, then they are overwritten. The color of the mixture is selected contrasting or plain.

If the question arises: what is the best way to finish a doorway that does not have doors, the first thing to consider are options that include artificial stone, decorative brick and clinker.

Plaster

IN Lately such material has noticeably fallen in popularity. But just recently, about ten years ago, this method seemed the most accessible. It's safe to say that many simply underestimate plaster. Indeed, this option has several significant drawbacks - the complexity of application (in the absence of experience) and the presence of a certain amount of "dirt". But if you do all the work correctly, as well as achieve a combination with other products, then the effect will pleasantly surprise you.

How to decorate a doorway without a door by plastering:

The required amount of the mixture is prepared. The solution made should be in such quantity that it is enough for 30-45 minutes of work.
The mixture is applied to the surface by spraying. Leveling occurs using a rule or a wide spatula.
If required, beacons and perforated profile guides are installed.
When the solution layer exceeds 1-1.5 cm, then a reinforcing mesh is laid.

Such a surface can be painted. But it is better if the plaster acts as a starting composition. Then finishing decorative (textured) putty can act. It is applied in a certain order, which allows you to get amazing coverage. Such doorways will become an interior decoration.

Decorative plaster – spectacular option design of a doorway without a door

Arch device

The arch can transform the interior. It is important to understand that a device of this design requires a certain amount of experience. Indeed, in order to finish the doorway exclusively with your own hands, you will need to expend a lot of effort.

Should know! There are standard-sized arches that are already completely ready for installation. They just need to be carefully installed.

Arched doorway

The most simple are the arches made of drywall. It looks like this:

Finishing doorways begins with the installation of the frame on both sides. It is fixed on the upper horizontal and uprights. On the latter, it has a size that is almost equal to the end of the rounding.
GKL parts are fixed to the frame. An arc is pre-cut on them, for this a stencil is made.
Inside the resulting structure, an additional crate is performed. It serves to fasten the last arc-shaped drywall element.
The final finish is done with putty. Decorative cladding produced in various materials.

The arch can be done with more "noble" products, but will require more skill.

Other ways of registration

The design of doorways can be performed by other methods. They consist in the use of decorative curtains or screens. This method is very affordable and simple. In addition, it requires almost no work to be done.

Various options can be used:

Fabric curtains. They will be a great addition to any interior. The composition should be made in such a way that there is harmony with other elements and a combination with window decoration.
Bamboo curtains. This option is suitable when the room is made in eco style.
Thread curtains. These products are used if they want to fill the room with unusualness.

Of course, how to decorate the opening, everyone is chosen based on their taste and preferences.

Photo gallery: finishing options for doorways without doors (20 photos)

What can be done with an opening equipped with a door

Deciding how to make a doorway that has door leaf, involves the use of the most simple options. The only difference is where this structure is located.

A simple arrangement of interior space

Most affordable option finishes interior openings the installation of the box and adjacent elements is considered. General Technology is:

The box is installed. It can be equipped with a threshold or be without it.
As materials that will veneer the slopes, dobors are used. They are available in standard sizes (up to 120-150 mm).
These elements are attached due to the groove that is on the box. If such design feature not provided, then the fixation is carried out on self-tapping screws. A hole for them is drilled through the end of the part.
External decoration is made at the expense of platbands that frame the opening.

This option is great for situations where it is required to complete the cladding of not very wide structures.

Other options

How to ennoble a doorway that has a door in a more original way? In fact, to truly create interesting option, it is necessary to try. The fact is that it is the hinged canvas that limits the use of different materials. Improper use of finishing products - prevents opening. Although, considering this feature, then for exterior finish fits almost everything.

On a note! There is a sliding way to open the door. That is, the canvases repeat the arrangement of compartment doors. This is a rather interesting technological solution that requires a more careful choice of facing products.

How to finish a doorway? Such a question has many answers, which depend on the specific situation. But no matter what anyone advises, you still need to listen to your heart and choose the option that will be closest to you.

During repair work the owners may have a dilemma - whether to install or is it better to replace them with a more modern design option, for example, an arch. By removing the doors, you can solve several problems at once: decorate your home and save free space. That is why most people choose to alternatives. Let's figure out how to decorate a doorway beautifully and effortlessly, in the main pros and cons existing methods decorating passages between rooms, as well as the appropriateness of such redevelopment in various situations.

When are interior doors not required?

Interior opening can be varied

The answer to this question largely depends on the functional purpose of the premises that are planned to be combined, and individual features housing. Often the passage between the kitchen and the living room undergoes alteration. Such a redevelopment makes sense if the kitchen area is small. dining area at the same time, it can be transferred to the room, freeing up useful kitchen space.

No less relevant will be the replacement of the door with an arch or another design option for the opening, and if a balcony is attached to one of the rooms. This will provide smooth transition between them, and the two rooms seem to merge into one, which will visually enlarge the room.

It will also look good to pass, designed in the form of a portal, if there is a small dressing room located between front door and a corridor. But to make such an entrance to the bedroom, even if it is draped with curtains, is hardly appropriate.

Possible finishes

So, if you decide that the layout of your home allows you to refresh the interior by changing the look of the doorways, then first you should learn more about existing varieties such a finish. Consider some of the most popular ways to decorate the passage between rooms.

Arches in the doorway. What are they?

Arch

Installing an arch in a doorway is one of the most popular ways to design an entrance to a room. It can be done in several variations:

Oval. Such an arch is considered standard and has a rounded shape. To create it, you will need to round the corners of the opening with drywall and a metal frame.
Rectangle. The most easily implemented option that does not require the installation of additional structures.
complex forms. Giving the doorway a more exotic look is impossible without installing a complex drywall construction and, most likely, will require the involvement of builders-finishers.
Imitation. This type of arch is relevant if the door structure is of considerable size and does not look very nice in a rectangular form. To give such a passage a rounded shape, semicircular segments are installed at its corners.

All types of arches, except for unusual shapes, are quite simple to implement. However, there is a minus - they can not be installed in any room, because a considerable ceiling height is required for the arrangement. Therefore, for those who are not very lucky with this parameter, it is better to choose a different decor option.

Stone decoration is always in fashion

A bright accent in the interior will be a doorway painted in contrasting colors or highlighted with various facing materials. And stone decoration for this purpose is one of the best solutions. Stone for decoration can be used both natural and artificial. The first is used less frequently due to its high cost and less ease of installation and operation.

stone finish

Installation natural stone- the process is not easy, and it is better to entrust it to professionals. But it is quite possible to cope with the lining with artificial panels “under the stone” on your own, fixing them tile adhesive. At the same time, in appearance, they will practically not be inferior to the real material.

Note! In order for the stone finish to harmonize with the rest of the interior, it is worth placing objects in the room with elements of a similar material, for example, a framed mirror, shelves, wall panels or fake fireplace.

Stucco decoration: beautiful and practical

When decorating doorways, polyurethane stucco molding is also very popular. It has many advantages: it is easy to attach, durable enough, besides, initially having a white color, it lends itself well to painting.

But, when deciding on the design of this material, you need to remember that it often looks very cumbersome. Therefore, if the rooms are small, it makes sense to choose not embossed, but flat elements, so as not to visually overload the room.

Curtains in the doorway: an affordable solution

Curtains are the perfect solution!

Drapery with curtains is another way to ennoble a doorway. The advantage of this type of design is that it not only allows you to emphasize the passage between the rooms, but also, if necessary, hide it. The advantages also include ease of installation, affordability and wide choose colors and materials.

Curtains in the doorway can be both fabric and in the form of "pendants". Ordinary traditional curtains can be used as fabric curtains, but it is better to purchase products specially designed for this purpose.

The so-called "pendants" for decorating doors are used more often. They can cover the entire opening or have the form of a frame. The material for their manufacture is wood, plastic, bamboo, various cords, beads, etc. If you wish, you can easily make such a decoration with your own hands.

Video on creating a door arch with your own hands

In this section, we suggest that you familiarize yourself with the features of installing and decorating a door arch with your own hands. The video will help you understand all the nuances of this case.

Photo of interiors with an interesting decor of the door space

As you can see, there are many options for designing a doorway. We have described only a part of them, but in reality there are many more of them, and anyone who decides to replace the boring and standard door structure to something more original, he will be able to find a solution to his liking. The photos below will help you make a choice and get some interesting ideas.

Arches continue to hold the palm of leadership among the decorative finishes of doorways. This is not surprising, because in addition to the classic rounded shape, there are many other variations. For example, after performing a small redevelopment and expanding the entrance to the room, you can install an arch with niches or shelves. It will not only add variety to the interior, but also be able to serve as a stand for indoor plants, your photos or souvenirs.

Those who like minimalism can opt for a simple but original arch in the shape of a circle.

For lovers of luxury, this way of decorating doors also opens up a lot of opportunities. The arch, finished with polyurethane stucco, will turn your home into a real palace.

Do not forget about the curtains. Such curtains made of bamboo will perfectly fit into the interior, decorated in ethnic style.

Another original option is thread curtains. They look very gentle, but at the same time bright, and a variety of colors allows you to choose curtains that are ideal for your home.

Making an opening without a door implies several features. Not all materials are suitable for this type of finish, and the selected options will have to be handled quite carefully. Some designs can be created with your own hands, and the construction of the rest is best left to a professional.

Peculiarities

The logical conclusion would be that a doorway without a door is made completely without a door frame. All decoration includes only the lining of the opening itself, which is performed using a variety of materials.

The design of a doorless opening allows you to choose from a variety of forms, including both classic and fantasy interesting options.

Far from every room, an opening without a door will look appropriate. There are some rooms that must have a door, and these include not only a toilet and a bathroom. Bedroom, kitchen, study must be equipped with a full door because in these rooms more than others there is a need for privacy and intimacy.

However, every rule can be circumvented. For additional decoration of such openings, curtains, muslin, screens are used. They allow you to create the illusion of dividing the room, while not completely replacing the door.

Upgrading an open doorway implies relying on the integrity of the entire home. As a rule, identical doorless openings are made in an apartment or house. This applies to both form and finish. They act as a connecting element, uniting all rooms into a single ensemble.

Speaking about the advantages that open openings have compared to classic doorways, one cannot fail to mention space saving. Each door occupies at least square meter usable area. When creating a doorless design, this problem disappears. From an aesthetic point of view, the opening allows you to visually expand the space or expand the functional area of \u200b\u200bthe room by combining it with a utility room. good example is a frequent recently association of a balcony and a living room.

In some cases, a doorless space looks much more attractive than a door, especially when it is beautifully designed. For example, shelves are often placed along the contour of such an opening. Statuettes or other little things placed on them beautifully frame the gap, creating a unique atmosphere that cannot be repeated. Thus, sometimes an open opening looks even more intimate than a thick oak door.

Finally, one more important advantage is creating adequate ventilation in the apartment. Air circulates better through open space, and for small apartments, for example, as in Khrushchev-built houses, this factor is important - it allows you to fight stuffiness.

Creating several openings can completely change the original layout of the apartment, but in reality it comes out much cheaper than a full redevelopment.

In addition, the opening is often allowed to be created even in bearing wall, so there are much more options for a new apartment plan.

Kinds

There are many different configurations of doorways without a door, which differ from each other not only in their shape, but also in the material with which they are created. Along with traditional raw materials, are used and latest developments in the field of design.

The simplest design is ordinary rectangular span. Creating a rectangular opening is very simple: the door frame is completely dismantled, then the surface of the walls is leveled along the contour. In the future, the resulting gap is simply painted or lined suitable material. There are a great many ways to finish, from the simple installation of wooden doborniks to the creation of pompous stucco columns.

More popular building arched structures. To do this, it is not necessary to expand the existing opening in the wall, in last years the idea of creating false arches is actively used. In this case, corner elements made of polyurethane or drywall with rounded sides are installed in a rectangular span, and the result is a full-fledged arch at a much lower cost and labor. However, this method is not suitable for all dwellings: it is necessary that the opening has sufficient height.

There are several types of arches:

Round arch. It is a classic interpretation and can be used in absolutely any room, regardless of the parameters, but there is one unspoken rule. The lower the ceiling, the wider the arched span should be.
Trapezoidal span. It is created from straight lines and can only be called an arch conditionally. Designers do not advise using such a form because of the stable association with a funeral accessory - a coffin.
Triangular arch. There are a huge number of subspecies of triangular arches: keeled, lancet horseshoe, Tudor. Similar elements came to modern design from the Middle Ages, and they are used preferably in high spacious rooms.

More and more often people refuse to create ordinary classic openings in favor of fantasy asymmetric ones.

They can only be made in plasterboard partition walls. Asymmetric openings can have any shape, and can also be supplemented with all sorts of auxiliary details: shelves, niches, lighting. Such a design acts as bright element and sets the tone for the entire look of the room. Eye-catching, an asymmetric opening helps to hide possible flaws when repairing a room.

Dimensions

It is possible to balance the proportions of the premises in the apartment with the help of doorways without doors. Depending on whether the opening is wide or narrow, high or low, the impression produced varies.

For rooms with low ceilings, it is strongly not recommended to mount narrow spans. Visually, they will make the room tiny and uncomfortable. It is better to choose a wide option that will visually expand the area of \u200b\u200bthe room, add air and light to it. This applies not only to arched openings, but also to rectangular ones.

Optimal Height also depends on the original proportions of the room. If you want to combine two rooms with the help of a gap, it is recommended to make it almost as high as the ceiling. An ordinary span, which serves only as an alternative to a door, should be made much lower, but its height should not be lower than 2 m. In the case of arches, this indicator grows by at least 30 cm. This is due not so much to aesthetic rules as to safety requirements: a person can hit hard on the upper narrow part of the arch in the dark.

When constructing asymmetric structures, the following rule should be followed: the more intricate the shape, the wider the opening should be. Too much concentration of monograms and other elements on small space overload the view, making the design unnecessarily pretentious and cumbersome. As a result, instead of a spectacular accent, you will get a tasteless option that you will soon get tired of.

Thus, the size of the doorway is more determined by the characteristics of the room itself, and not by the chosen shape.

Remember that very wide doorways are best designed using some kind of texture, such as embossed moldings. If you use an ordinary smooth cladding, the clearance will be “lost” against the general background of the room and, from an aesthetic point of view, will not look particularly harmonious.

In various rooms

In the vast majority of cases, the expediency of installing a doorless opening is obvious, however, sometimes refusing a door is highly undesirable. Among the rooms in which it is best to leave the door is the kitchen. This is especially true in small apartments where a strong kitchen smell will be particularly annoying. It is not always pleasant when aromas are felt in the living room or bedroom.

The old bored interior of the living room can be changed beyond recognition, at the same time competently expanding the usable area. If you refuse a separate balcony block and from the door to the balcony, it will turn out to make the living room brighter. The balcony will certainly need to be furnished in a style similar to the living room, since the rooms, united by a doorless skylight, should be perceived as a single whole.

You can often encounter cases when they refuse the door between the corridor and the dressing room. Since both of these rooms are quite small and cramped, such a move helps to hide this fact, allowing people to feel more free.

In small apartments, they refuse doors between the hallway and the living room, especially if the apartment is one-room. So the whole area is perceived as a single whole, as a result of which the dwelling seems larger.

In cases where such a small apartment has low ceilings, it is better not to choose an arched shape as an opening. It is much more logical to stop at the classic rectangular span.

Quite rarely they refuse the door to the bedroom, but they do not dare to completely leave the entrance “defenseless”. Come to the rescue blackout curtains or screens, which perfectly protect the intimacy of the room. If necessary, they can be easily and quickly dismantled. An interesting solution is the use of curtains with pickups: at night they can be completely closed, and during the day they will serve as a beautiful frame for the opening.

How to arrange?

The opening is cashed different materials and in different techniques. You can decorate the interior span with your own hands, or you can turn to professionals who will create a complex and unique decor.

A good idea is to decorate the doorway with curtains.

decorative curtain plays the same role as the door in psychological terms, but it takes much less space. If desired, the curtains can be completely removed without any problems or replaced with others, while the design of the opening will not suffer (for example, if you just remove the door leaf, loops will remain on the span that do not look very attractive).

Another option on how to decorate a doorway without a door is to use additional elements design - various stucco panels. With their help, it will be possible to ennoble any gap, regardless of how smooth walls and in what colors the opening is made. Finishing is extremely simple and often done completely independently.

With the help of stucco molding, it is possible to decorate openings in various styles. For example, you can make a classic arch with columns and heavy curly elements. If you add gilding, you can completely recreate the spirit of baroque or classic. For modern interiors more appropriate is the use of simple relief moldings with geometric patterns, such as embossed groove lines. If in the first case it was appropriate to opt for pilasters and capitals, then in the second case they should be avoided.

Stucco molding can be found quite rarely, it has practically fallen out of use in recent times. This is due to the relatively small size modern apartments, because in small spaces intricate designs look ridiculous. You should not completely abandon the stucco elements: some of them can help expand the room.

Also, for the design of doorways without doors, artificial stone masonry, clinker tiles or drywall are often used.

materials

Facing a doorway without a door can be done using a variety of materials. The simplest solution is to paint the gap or paste over it with the same wallpaper as the walls. However, there is one “but”: only perfectly even walls are suitable for this, otherwise the whole structure will not look neat enough and made as if hastily.

Another option is to make a box of extensions and put it in the gap or sheathe it MDF panels. In both cases, you get a wooden gap that looks stylish and can be harmoniously integrated into almost any interior.

Framing the opening is best done with valuable wood or its imitation, since it is these solutions that look the best.

It is also possible to sheathe the clearance with drywall. Drywall is a truly unique material. With its help, it is possible to form a structure of almost any configuration, supplementing it with elements from other lightweight materials, such as polyurethane.

A simple plasterboard opening can be easily done on your own, and it will not take much time, but the effect will please.

Often the gaps are laid out with imitation stone or clinker tiles. Clinker tiles imitate brick, while it weighs several times less. They produce tiles of different shapes: there are classic elements, as well as special corner ones. There are a wide variety of sizes on the market, but medium-sized tiles are the most popular. The seams between the tiles are usually rubbed with a compound that exactly imitates the main wall covering.

Artificial stone looks more interesting than clinker tiles. There are imitations of various materials: limestone, marble, malachite and many others. This material has a lot of advantages: such a cladding looks expensive, harmonizes perfectly with other finishing materials, differs long term service and wear resistance, as well as very easy to clean. The laying of such material can be carried out either in a geometrically well-thought-out order, or randomly - both options look equally successful.

Both tiles and stone are fixed either on tile adhesive (when the walls under them are not aligned well enough), or on liquid nails (if the walls have a perfectly flat surface).

How to do it yourself decorative arch lined with gypsum stone and bas-reliefs, see the next video.

Options in the interior

A rather simple opening with a slightly curved edge adds pomposity and grandeur to the room. Its unusual structure is made in rather restrained proportions: straight lines are used, there is no complex decoration. The almost even square shape contributes to the visual preservation of the proportions of the room, without creating any visual illusions.

Usage natural materials welcome when creating the design of a doorless opening. Wood and raw stone harmonize well with each other, despite the fact that the tree was selected of valuable species, and the stone is the most ordinary. The play on contrasts deserves special attention: firstly, wood and stone contrasting in color are used, and secondly, the even edge of the wooden casing is adjacent to the torn edges of the masonry.